Airtac BSE Clamp Standard Cylinder BSE32X700S
The AirTAC Airtac BSE Clamp Standard Cylinder BSE32X700S is a genuine double-acting ISO 15552 cylinder with an integrated spring-applied, air-released ROD LOCK. If air is cut or an E-stop is hit, the collet clamps the Ø12mm rod and holds up to 600 N in either direction — no drift. Ø32mm bore, 700mm stroke, PT1/8 cylinder ports, G1/8 lock-release port.
- BoreØ32 mm
- Stroke700 mm
- Static holding force600 N
- Lock typeSpring-lock / air-release
- Cylinder portPT1/8
- Lock-release portG1/8
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac BSE Clamp Standard Cylinder BSE32X700S
The AirTAC BSE32X700S is a double-acting single-rod ISO 15552 profile cylinder with an integrated spring-applied, air-released rod lock. It features a 32 mm bore, 700 mm stroke, and a magnetic piston for position sensing.
The fail-safe collet lock provides a 600 N bidirectional static holding force with no live air. Operating pressure is capped at 0.7 MPa. A separate G1/8 release port unlocks the clamp, which is entirely distinct from the adjustable air cushions at both ends.
Rod Lock — 600 N Static Holding (Ø32mm)
A spring clamps the collet onto the rod, so the Airtac BSE Clamp Standard Cylinder BSE32X700S holds its position in both directions when air is lost, exhausted or an E-stop trips. Apply 0.15–0.7 MPa to the G1/8 release port to unlock. Engage the lock only after the rod has stopped (it is not a dynamic brake), and release only when the pressures on both sides of the piston are balanced. Allow at least 0.5 s for full release before moving.
Airtac BSE Clamp Standard Cylinder BSE32X700S Technical Specifications
| Model | Airtac BSE Clamp Standard Cylinder BSE32X700S |
|---|---|
| Series | BSE ISO 15552 rod-lock cylinder |
| Bore size | Ø32 mm |
| Stroke | 700 mm |
| Static holding force | 600 N |
| Cylinder port | PT1/8 |
| Lock-release port | G1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Unlocking pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 700 mm |
Specifications follow the official AirTAC BSE datasheet. The lock uses the SE standard body; SE mounting accessories fit BSE except FTC. Port options: PT (standard) / G (BSPP); lock-release port is G1/8.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa (max) | 563 N | — |
| Max drive (@0.7 MPa) | 57 kgf | |
Drive force is separate from the 600 N static holding force of the lock. BSE operates up to 0.7 MPa. Size with a safety margin.
Model Code: Airtac BSE Clamp Standard Cylinder BSE32X700S
| B | Rod-lock cylinder prefix. |
|---|---|
| SE | ISO 15552 standard double-acting body. |
| 32 | Bore size in mm. |
| ×700 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Thread: PT (blank) / G. Mounting (BSE): Basic, LB, FA, FB, CA, CB, CR, TC (FTC is not available on BSE). Related: SE (no lock), BSED (double-rod rod lock). Sensors CMSE/DMSE fit magnetic BSE.
Where the Airtac BSE Clamp Standard Cylinder BSE32X700S Is Used
Small Vertical Lifts
Holds light 600 N vertical loads in place instantly if compressed air is exhausted, preventing sudden drops on small packaging elevators.
Pneumatic Tooling Clamp
Secures a 32 mm bore actuator gripping a workpiece, ensuring the collet lock maintains position during an emergency stop without needing live air.
Sorter Diverter Arm
Locks a 700 mm stroke diverter in its extended or retracted position with 600 N of static hold when the conveyor line halts for maintenance.
Is the Airtac BSE Clamp Standard Cylinder BSE32X700S the Right Cylinder?
Verify your load stays below the 600 N holding force. If you need less holding, no smaller BSE bore exists. If you need more drive or hold, the 40 mm bore offers 628 N push at 0.5 MPa and 900 N holding force. Always engage the lock only after the rod stops, and allow at least 0.5 s for full release after balancing piston pressures before moving.
With a 700 mm stroke, use a guide to prevent side-load damage to the seals and front cap. This -S variant includes a magnet for CMSE reed or DMSE electronic sensors. SE mounting accessories fit this body, except FTC.
Quick checklist
- ✓ Load to hold ≤ 600 N?
- ✓ Fail-safe hold on air loss / E-stop needed
- ✓ Lock engaged only when stopped
- ✓ G1/8 release-air line available
- ✓ Magnet (-S) for CMSE/DMSE sensors?
Installation & Safety Notes
- check Engage the lock only after the rod has stopped — not as a dynamic brake.
- check Release only when both piston sides are pressure-balanced.
- check Allow ≥0.5 s for full release before commanding motion.
- check Feed the G1/8 release port with 0.15–0.7 MPa clean air.
- check Add safety-rated controls for man-rated / overhead loads.
- check Use SE mounting accessories (FTC excepted).
Airtac BSE Clamp Standard Cylinder BSE32X700S FAQ
The spring-applied collet engages instantly on air loss, providing a 600 N static hold. The drive forces are 402 N push and 345 N pull at 0.5 MPa, 563 N push at 0.7 MPa, with a max drive of 57 kgf.
Balance the air pressures on both sides of the piston first. Then supply 0.15-0.7 MPa to the separate G1/8 release port, and wait at least 0.5 seconds for the collet to fully retract before commanding movement.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC BSE Cylinders
Request a Quote for Airtac BSE Clamp Standard Cylinder BSE32X700S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.