This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACED16X15S, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD16X15S
The AirTAC ACPD Double Rod Compact Cylinder ACPD16X15S is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø16mm bore and 15mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED16X15S (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ16 mm
- Stroke15 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod
- Rod threadM4×0.7
- StatusDiscontinued → ACED16X15S
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD16X15S
This AirTAC ACPD16X15S is a double acting compact cylinder with a rod leaving both covers, so the 8 mm through-rod delivers an equal 75.4 N at 0.5 MPa in each direction and 105.6 N at 0.7 MPa. The 16 mm bore runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi) with speeds of 30-500 mm/s. Because the body follows the short ISO 21287 class, it saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, which is why it slots into slim fixtures and tight gantries. Note: this model is discontinued; the current-production successor is ACED16X15.
The hard-anodized aluminium body carries fixed TPU bumpers at both ends, and the S45C hard-chrome rod resists wear in continuous cycling. The -S code on this unit means the magnet is fitted, so CMSE or DMSE reed and solid-state switches can be clipped on for end-of-stroke sensing. Confirm ISO 21287 mounting dimensions before swapping to the ACED16X15.
Airtac ACPD Double Rod Compact Cylinder ACPD16X15S Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD16X15S |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED16X15S |
| Bore size | Ø16 mm |
| Stroke | 15 mm |
| Acting type | Double acting, double rod |
| Port size | M5×0.8 |
| Rod thread | M4×0.7 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 75 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED16X15S (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 75 N |
| 0.7 MPa | 106 N |
| Max (@1.0 MPa) | 15 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD16X15S
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 16 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD16X15S Is Used
Small-part ejection on assembly stations
The short 15 mm stroke and equal 75.4 N push-pull at 0.5 MPa suit pushing finished electronics components off a nest into a chute where body length is limited.
Position-flagged test fixtures
With the -S magnet fitted, CMSE or DMSE switches confirm clamp state on a PCB test jig, while the rear rod carries a second flag for a redundant signal.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD16X15S with the ACED16X15S
For a 15 mm stroke at this force level, the 16 mm bore gives 75.4 N both ways at 0.5 MPa; step down to the 12 mm bore (42.4 N) for lighter clamping or up to the 20 mm bore (117.8 N) if the load grows. The through-rod resists rotation and side load, and the rear rod can carry a sensor flag. The female M4x0.7 rod thread and PT ports suit standard fittings. This cylinder does not hold position when air is lost - add a rod lock or pilot check for a held load. Since the ACPD is discontinued, order the ACED16X15 as the direct replacement and verify the ISO 21287 hole pattern.
Replacement checklist
- ✓ Current-production ACE → ACED16X15S
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD16X15S FAQ
Because a rod exits both covers, force is equal both ways: 75.4 N at 0.5 MPa and 105.6 N at 0.7 MPa, with a maximum of 15.4 kgf at 1.0 MPa. Both strokes use the rod-side area, so there is no push-pull difference. Operating range is 0.15-1.0 MPa (22-145 psi) at 30-500 mm/s.
The short-body build saves about 50% of the mounting length of an ISO 15552 profile cylinder, and FA/FB flange or LB foot brackets bolt to the standard face. The -S code on this model means the magnet is fitted, so CMSE and DMSE reed or solid-state switches mount directly. The model is discontinued - the ACED16X15 is the current replacement; confirm ISO 21287 mounting dimensions before swapping.
Related AirTAC ACE Cylinders
Request a Quote for the ACED16X15S
Send us the quantity and destination. We confirm price, stock and lead time on the ACED16X15S replacement — usually within 7-8 hours.