This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACED16X200B, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD16X200B
The AirTAC ACPD Double Rod Compact Cylinder ACPD16X200B is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø16mm bore and 200mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED16X200B (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ16 mm
- Stroke200 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod
- Rod threadM4×0.7
- StatusDiscontinued → ACED16X200B
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD16X200B
This is a double acting compact cylinder with a rod leaving both covers, so the 16 mm bore delivers the same 75.4 N at 0.5 MPa (105.6 N at 0.7 MPa) on every stroke, since both sides work on the rod-side area. The through-rod resists rotation and light side load, and the rear rod can carry a sensor flag or a second tooling plate. The 200 mm stroke is a made-to-order length, because bore 16 tops out at 75 mm as a standard size.
The short ISO 21287-class body saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, which is why this bore and stroke suit slim gantries and sliding guards. A fixed TPU bumper sits at each end, the hard-anodized aluminium body carries an S45C hard-chrome rod, and speed runs 30-500 mm/s. Note this model is discontinued: the current direct is ACED16X200, so confirm ISO 21287 mounting dimensions before you swap. Plan on about 45 N (roughly 4.6 kg) of real work at 0.5 MPa rather than the full 75.4 N rating.
Airtac ACPD Double Rod Compact Cylinder ACPD16X200B Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD16X200B |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED16X200B |
| Bore size | Ø16 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod |
| Port size | M5×0.8 |
| Rod thread | M4×0.7 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 75 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED16X200B (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 75 N |
| 0.7 MPa | 106 N |
| Max (@1.0 MPa) | 15 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD16X200B
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 16 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD16X200B Is Used
Reciprocating test slider
The through-rod drives a small inspection carriage back and forth over a 200 mm travel, with equal 75.4 N force in each direction for symmetric cycle times.
Two-sided gate actuator
Front and rear rods push the same sliding guard or diverter from either end, and a rear-mounted flag can trip a position check on the return stroke.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD16X200B with the ACED16X200B
At 75.4 N per direction this bore sits between the 12 mm unit (42.4 N) and the 20 mm unit (117.8 N) at 0.5 MPa, so step up to 20 mm if your tooling needs more than about 45 N of usable force. The 200 mm stroke is non-standard for bore 16 and is built to order. The B code gives a male M4x0.7 rod thread; the port is M5x0.8. A plain double-rod cylinder drifts when air is lost, so add a rod lock or pilot check for a held load. No magnet is fitted on this code; order the -S variant if you want CMSE / DMSE switches. Replacement: ACED16X200.
Replacement checklist
- ✓ Current-production ACE → ACED16X200B
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD16X200B FAQ
Because a rod exits both covers, force is equal in both directions: 75.4 N at 0.5 MPa and 105.6 N at 0.7 MPa, with a maximum of 15.4 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) and speed is 30-500 mm/s.
The ACPD family is out of production. Order ACED16X200, the ISO 21287 successor with the same 16 mm bore, 200 mm stroke and force class, and verify the ISO 21287 mounting dimensions against your fixture before swapping, since the ACP was built to the older DIN-standard format.
Related AirTAC ACE Cylinders
Request a Quote for the ACED16X200B
Send us the quantity and destination. We confirm price, stock and lead time on the ACED16X200B replacement — usually within 7-8 hours.