This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACED63X65, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD63X65
The AirTAC ACPD Double Rod Compact Cylinder ACPD63X65 is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø63mm bore and 65mm stroke, 1/8" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED63X65 (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ63 mm
- Stroke65 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM10×1.5
- StatusDiscontinued → ACED63X65
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD63X65
The ACPD63X65 is a double acting, double-rod compact cylinder in the DIN-standard ACP family, now discontinued. A 16 mm rod exits both covers, so the 63 mm bore delivers an identical 1458.1 N at 0.5 MPa (2041.3 N at 0.7 MPa) on every stroke, since both sides work on the rod-side area. The through-rod resists rotation and side load, gives a symmetric mount, and the rear rod can carry a sensor flag. A fixed TPU bumper sits at each end and the rod runs at 30-500 mm/s.
The hard-anodized aluminium body follows the ISO 21287 short format, saving roughly 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight gantries and guarding where a full-length body cannot. The magnet is not fitted on this code; order the -S variant if you need CMSE or DMSE switches. Replacement: ACED63X65, the current-production ISO 21287 direct.
Airtac ACPD Double Rod Compact Cylinder ACPD63X65 Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD63X65 |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED63X65 |
| Bore size | Ø63 mm |
| Stroke | 65 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 250 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED63X65 (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD63X65
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 63 | Bore size in mm. |
| ×65 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD63X65 Is Used
Reciprocating transfer carriage
The through-rod drives a pallet shuttle on both faces of a 65 mm stroke, pushing and pulling with the same 1458.1 N at 0.5 MPa so the return leg needs no derating.
Fixture clamping from either side
A jig builder uses the rear rod to actuate a second clamp, letting one 63 mm cylinder serve two clamp points with equal force and a symmetric mount.
Gantry position flagging
On a pick station, the back-end rod carries a flag for a switch when the -S magnet is ordered, giving end-of-stroke signals in a body about 50% shorter than an ISO 15552 profile cylinder.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD63X65 with the ACED63X65
At 65 mm stroke this sits well inside the 250 mm maximum standard stroke for the 63 mm bore, so it is a catalog item, not a made-to-order build. If 1458.1 N at 0.5 MPa is more than the job needs, the 50 mm bore gives 881.2 N; if you need more, the 80 mm bore reaches 2356.2 N. Remember that a plain double-rod cylinder drifts when air is lost, so add a rod lock or pilot check for a held load. FA/FB flange and LB foot mountings bolt to the ISO 21287 face, and the -S code adds the magnet for CMSE / DMSE switches. For new projects, specify ACED63X65 and confirm the ISO 21287 mounting dimensions before swapping.
Replacement checklist
- ✓ Current-production ACE → ACED63X65
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD63X65 FAQ
Yes. Because a 16 mm rod exits both covers, both strokes use the rod-side area: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa, equal every way, with a maximum of 297.4 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), speed 30-500 mm/s, air filtered to 40 um, temperature -20 to +70 C.
Order ACED63X65, the current-production ISO 21287 successor: swap the P for an E and you keep the same 63 mm bore, 65 mm stroke and force class. The ACP is DIN-standard, so confirm the ISO 21287 mounting dimensions before swapping. FA/FB flange and LB foot brackets, plus the optional -S magnet for CMSE / DMSE switches, are selected the same way.
Request a Quote for the ACED63X65
Send us the quantity and destination. We confirm price, stock and lead time on the ACED63X65 replacement — usually within 7-8 hours.