This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACED63X75B, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD63X75B
The AirTAC ACPD Double Rod Compact Cylinder ACPD63X75B is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø63mm bore and 75mm stroke, 1/8" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED63X75B (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ63 mm
- Stroke75 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM10×1.5
- StatusDiscontinued → ACED63X75B
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD63X75B
A double acting compact cylinder with a rod leaving both covers, the ACPD63X75B pushes and pulls with identical output: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa in either direction, since both strokes work on the rod-side area. The 63 mm bore drives a 16 mm through-rod over a 75 mm stroke, with a male rod thread (B code) on each end and a fixed TPU bumper at both covers. Speed range is 30-500 mm/s across a 0.15-1.0 MPa (22-145 psi) supply.
The hard-anodized aluminium body follows the ISO 21287 short format, cutting roughly 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into cramped gantries and fixture plates. Note that this model is discontinued: the current-production direct is ACED63X75, so confirm the ISO 21287 mounting dimensions before swapping. The magnet is not fitted here; order the -S code if you need CMSE / DMSE switch sensing.
Airtac ACPD Double Rod Compact Cylinder ACPD63X75B Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD63X75B |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED63X75B |
| Bore size | Ø63 mm |
| Stroke | 75 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 250 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED63X75B (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD63X75B
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 63 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD63X75B Is Used
Reciprocating conveyor pushers
The through-rod drives a pusher plate from either side with equal 1458.1 N force, so diverting cartons on a packaging line feels identical in both directions.
Symmetric slide actuation on gantries
A rod at each end lets a 75 mm stroke drive a linear slide from the rear while the front rod carries a sensor flag, keeping the mount balanced on pick-and-place frames.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD63X75B with the ACED63X75B
At 1458.1 N per direction this bore sits between the 50 mm (881.2 N) and 80 mm (2356.2 N) versions, so step down for lighter clamping or up for heavier presses. Because it is a plain double-rod unit, the piston drifts when air is lost - add a rod lock or pilot check if a load must stay put. FA/FB flange, LB foot, CA/CB clevis, CR, SDB pivot and FTC brackets bolt to the standard face, and the optional -S magnet enables CMSE / DMSE switches. For new designs, order ACED63X75 instead, as the ACPD line is discontinued.
Replacement checklist
- ✓ Current-production ACE → ACED63X75B
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD63X75B FAQ
Because a rod exits both covers, force is equal both ways: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa, with a maximum of 297.4 kgf at 1.0 MPa. There is no larger push than pull - both strokes use the rod-side area of the 63 mm bore with the 16 mm rod deducted.
The hard-anodized aluminium body follows the ISO 21287 short format, saving about 50% of the mounting length of an ISO 15552 profile cylinder, and the fixed TPU pad at each end simply decelerates the piston near the ends of travel. The ACPD63X75B is discontinued; ACED63X75 is the current direct successor in the same bore, stroke and force class - confirm the ISO 21287 mounting dimensions before swapping.
Related AirTAC ACE Cylinders
Request a Quote for the ACED63X75B
Send us the quantity and destination. We confirm price, stock and lead time on the ACED63X75B replacement — usually within 7-8 hours.