Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X10SCA
The AirTAC Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X10SCA is a genuine double acting + cushion standard round-body mini air cylinder with a Ø0mm bore and 10mm stroke, PT/G air ports and a stainless-steel barrel with a hard-chrome-plated rod for reliable, mildly corrosion-resistant service. A variable air cushion at both ends lets you tune end-of-stroke deceleration on site.
- BoreØ0 mm
- Stroke10 mm
- Port sizePT/G
- Acting typeDouble acting + cushion
- Rod thread
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X10SCA
Ten millimetres of travel, 100.5 N of push: the MAC16X10SCA is made for short, punchy eject and clamp moves where a longer cylinder would waste space. It is double acting with needle-adjustable air cushions at both ends, running 30-800 mm/s on 40 um filtered air at 0.15-1.0 MPa (22-145 psi).
A riveted stainless barrel, hard-chrome 6 mm rod and aluminium covers keep it alive through coolant mist and washdown. The CA pivot back cover swings inside a die or fixture linkage, and the standard built-in magnet lets a CMSG / DMSG / EMSG switch report position out of the box.
Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X10SCA Technical Specifications
| Model | Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X10SCA |
|---|---|
| Series | MAC mini cylinder |
| Bore size | Ø0 mm |
| Stroke | 10 mm |
| Acting type | Double acting + cushion |
| Port size | PT/G |
| Rod thread |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MA-series datasheet. Barrel: stainless-steel tube (round-body, riveted rolling-packed construction); piston rod: carbon steel with 20µm hard-chrome plating; covers: aluminium alloy. Thread options: PT (blank) / G / NPT. Every MA-series cylinder ships with a built-in magnet for CMSG / DMSG / EMSG position sensors.
Theoretical Output Force (Ø0mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 0 N | 0 N |
| 0.7 MPa | 0 N | 0 N |
| Max (@1.0 MPa) | 0 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X10SCA
| MAC | Standard round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 0 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| -S | Built-in magnet for CMSG / DMSG / EMSG sensors (standard on MA series). |
| CA / U / CM | Back-cover type: CA pivot, U flat-end, CM round-end. |
MA-family variants: MA / MAC (double acting ±cushion), MSA / MTA (single acting push / pull), MAD / MACD (double rod ±cushion), MAJ / MACJ (double rod, adjustable stroke ±cushion), MAR (cushioned with integrated F/U mount). Mounting accessories: FA flange, LB foot, SDB pivot; plus I and Y knuckles. Thread PT (blank) / G / NPT.
Where the Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X10SCA Is Used
Die ejector pin drive
Ten mm of travel is enough to free a finished stamping from a small progressive die, pushed by 100.5 N at 0.5 MPa.
Checkweigher reject finger
A short, fast flick nudges underweight coffee packs off the belt; at 800 mm/s the 10 mm move completes in a fraction of a second.
Test-probe lift on PCB fixtures
The rod lifts a spring-probe block 10 mm so an operator can swap boards, and a CMSG switch confirms the clamped position.
Is the Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X10SCA the Right Cylinder?
Ten millimetres suits ejection and flick moves; beyond roughly 15 mm of travel, move up in stroke, and beyond 100.5 N of push, move up to the 20 mm bore at 157 N and 0.5 MPa. On such a short stroke, open both cushion needles before first run so the rod does not hammer the covers at speed. Air loss leaves the rod unheld - a pilot check valve keeps a part clamped if that matters. Mount with the CA pivot plus FA flange, LB foot or SDB options and an I or Y knuckle.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) is standard for sensors
- ✓ Back cover (CA/U/CM) & mount (FA/LB/SDB)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check On first run, back off the cushion screws and release gradually.
- check Installation by qualified personnel per AirTAC docs.
Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X10SCA FAQ
Push is 100.5 N and pull 86.4 N at 0.5 MPa; at 0.7 MPa the numbers become 140.7 N and 120.9 N, and theoretical maximum is 20.5 kgf at 1.0 MPa. Stroke is 10 mm and speed spans 30-800 mm/s.
Short ejector and clamp linkages still need a swinging joint, and the CA end provides the pin without adapters. The stainless round barrel stands up to coolant mist, and the built-in magnet suits CMSG / DMSG / EMSG switches for confirming the 10 mm move.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X10SCA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.