Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X200SCM
The AirTAC Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X200SCM is a genuine double acting + cushion standard round-body mini air cylinder with a Ø0mm bore and 200mm stroke, PT/G air ports and a stainless-steel barrel with a hard-chrome-plated rod for reliable, mildly corrosion-resistant service. A variable air cushion at both ends lets you tune end-of-stroke deceleration on site.
- BoreØ0 mm
- Stroke200 mm
- Port sizePT/G
- Acting typeDouble acting + cushion
- Rod thread
- CushionVariable air cushion, both ends
About the Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X200SCM
Cushion control is the selling point here: the MAC16X200SCM uses needle screws at both ends to bleed its variable air cushion, so a 200 mm stroke can stop a small load smoothly at speed instead of hammering the covers. Push is 100.5 N and pull 86.4 N at 0.5 MPa, or 140.7 N at 0.7 MPa, with the CM round-end back cover ready to take a rod-eye knuckle for linked mechanisms.
The stainless-steel barrel and hard-chrome plated 6 mm rod stand up to splash and humidity far better than painted mini cylinders, and they run happily on 0.15-1.0 MPa (22-145 psi) filtered air. The piston magnet comes standard, ready for CMSG, DMSG or EMSG switches. In practice, size the job at around 60 N of working push at 0.5 MPa - roughly a 5 kg vertical lift with a 2:1 margin - rather than the full 100.5 N rating.
Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X200SCM Technical Specifications
| Model | Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X200SCM |
|---|---|
| Series | MAC mini cylinder |
| Bore size | Ø0 mm |
| Stroke | 200 mm |
| Acting type | Double acting + cushion |
| Port size | PT/G |
| Rod thread |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MA-series datasheet. Barrel: stainless-steel tube (round-body, riveted rolling-packed construction); piston rod: carbon steel with 20µm hard-chrome plating; covers: aluminium alloy. Thread options: PT (blank) / G / NPT. Every MA-series cylinder ships with a built-in magnet for CMSG / DMSG / EMSG position sensors.
Theoretical Output Force (Ø0mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 0 N | 0 N |
| 0.7 MPa | 0 N | 0 N |
| Max (@1.0 MPa) | 0 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X200SCM
| MAC | Standard round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 0 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Built-in magnet for CMSG / DMSG / EMSG sensors (standard on MA series). |
| CA / U / CM | Back-cover type: CA pivot, U flat-end, CM round-end. |
MA-family variants: MA / MAC (double acting ±cushion), MSA / MTA (single acting push / pull), MAD / MACD (double rod ±cushion), MAJ / MACJ (adjustable stroke ±cushion), MAR (cushioned with integrated F/U mount). Mounting accessories: FA flange, LB foot, SDB pivot; plus I and Y knuckles. Thread PT (blank) / G / NPT.
Where the Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X200SCM Is Used
Capsule lid clamp on a filling fixture
Presses a foil lid home on coffee capsule trays; 140.7 N at 0.7 MPa gives enough crimp pressure and the cushion keeps the clamp from battering the die.
Stopper pin on an indexing dial
Pops into dial holes to lock a rotary table between stations; the rod-eye knuckle absorbs small angular misalignment of the link.
Glue nozzle lift on a dotting bench
Drops a nozzle onto PCB pads for a datum dot; the 200 mm stroke clears the fixture and the standard magnet reports the down position.
Is the Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X200SCM the Right Cylinder?
There is no MAC bore below 16 mm, so this is the smallest option; a 20 mm bore lifts push from 100.5 N to 157 N at 0.5 MPa when more muscle is needed. Keep the 6 mm rod straight across the 200 mm stroke and support overhanging tooling, or side thrust will bow it. A dropped air supply leaves the piston free to move, so add a pilot check valve or rod lock when a held position counts. The CM round end takes an I or Y knuckle, while FA flange, LB foot and SDB pivot brackets handle fixed mounting; PT, G and NPT threads are selectable.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) is standard for sensors
- ✓ Back cover (CA/U/CM) & mount (FA/LB/SDB)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check On first run, back off the cushion screws and release gradually.
- check Installation by qualified personnel per AirTAC docs.
Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X200SCM FAQ
At 0.5 MPa: 100.5 N push and 86.4 N pull. At 0.7 MPa: 140.7 N push and 120.9 N pull. The theoretical maximum at 1.0 MPa is 20.5 kgf. It operates on 0.15-1.0 MPa (22-145 psi) of 40 um filtered air, proof tested to 1.5 MPa (215 psi), at 30-800 mm/s.
Its rounded face accepts an I or Y rod knuckle, letting the 200 mm stroke drive a pivoting link without adapters. Inside, the barrel is stainless steel rolled to the covers for splash resistance, and the piston magnet - standard on every unit - trips CMSG, DMSG or EMSG switches for signalling.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X200SCM
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.