Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X60SCM
The AirTAC Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X60SCM is a genuine double acting + cushion standard round-body mini air cylinder with a Ø0mm bore and 60mm stroke, PT/G air ports and a stainless-steel barrel with a hard-chrome-plated rod for reliable, mildly corrosion-resistant service. A variable air cushion at both ends lets you tune end-of-stroke deceleration on site.
- BoreØ0 mm
- Stroke60 mm
- Port sizePT/G
- Acting typeDouble acting + cushion
- Rod thread
- CushionVariable air cushion, both ends
About the Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X60SCM
With its CM round-end back cover, the MAC16X60SCM is a double-acting cushioned mini cylinder that suits compact assemblies needing a capped, low-profile rear. The 16 mm bore delivers 100.5 N push and 86.4 N pull at 0.5 MPa, and 140.7 N at 0.7 MPa - so budget around 60 N of usable force once you keep a healthy margin, enough to raise roughly 10 kg vertically or 5 kg with a 2:1 safety factor.
Inside sits a high-precision stainless tube rolled onto aluminium covers; outside, the 6 mm rod carries 20 um of hard chrome. That combination resists the condensation found near wash stations and outdoor conveyors. The variable cushion at each end is tuned by needle screws so loads can run faster without hammering the covers, and the standard magnet pairs with CMSG, DMSG and EMSG switches without a special order.
Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X60SCM Technical Specifications
| Model | Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X60SCM |
|---|---|
| Series | MAC mini cylinder |
| Bore size | Ø0 mm |
| Stroke | 60 mm |
| Acting type | Double acting + cushion |
| Port size | PT/G |
| Rod thread |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MA-series datasheet. Barrel: stainless-steel tube (round-body, riveted rolling-packed construction); piston rod: carbon steel with 20µm hard-chrome plating; covers: aluminium alloy. Thread options: PT (blank) / G / NPT. Every MA-series cylinder ships with a built-in magnet for CMSG / DMSG / EMSG position sensors.
Theoretical Output Force (Ø0mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 0 N | 0 N |
| 0.7 MPa | 0 N | 0 N |
| Max (@1.0 MPa) | 0 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X60SCM
| MAC | Standard round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 0 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -S | Built-in magnet for CMSG / DMSG / EMSG sensors (standard on MA series). |
| CA / U / CM | Back-cover type: CA pivot, U flat-end, CM round-end. |
MA-family variants: MA / MAC (double acting ±cushion), MSA / MTA (single acting push / pull), MAD / MACD (double rod ±cushion), MAJ / MACJ (adjustable stroke ±cushion), MAR (cushioned with integrated F/U mount). Mounting accessories: FA flange, LB foot, SDB pivot; plus I and Y knuckles. Thread PT (blank) / G / NPT.
Where the Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X60SCM Is Used
Carton flap tuck
Presses a cardboard flap down on a small packaging head, the cushion absorbing the press at the bottom of the 60 mm stroke.
Sorting flap on a conveyor
Flips a divert flap to steer blister packs into a reject chute; the round-end cover fits flush inside the conveyor side plate.
Guard latch on a dough line
Latches a machine guard that gets hosed down daily - stainless barrel and chrome rod outlast painted minis in the splash zone.
Is the Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X60SCM the Right Cylinder?
Compare before you commit: the same stroke in a 20 mm bore yields 157 N push at 0.5 MPa, while the 25 mm reaches 245.3 N - pick up a size if your load needs more than the 60 N practical force this bore offers. Supply it 0.15-1.0 MPa (22-145 psi). If your sequence must hold position between valve shifts, note the piston floats once air is lost; add a pilot check valve or rod lock rather than relying on the cushion. The CM round-end cover mounts through a clearance hole in your plate; FA flange and LB foot brackets bolt on when the frame needs a proper fixing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) is standard for sensors
- ✓ Back cover (CA/U/CM) & mount (FA/LB/SDB)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check On first run, back off the cushion screws and release gradually.
- check Installation by qualified personnel per AirTAC docs.
Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X60SCM FAQ
Push 100.5 N and pull 86.4 N at 0.5 MPa; push 140.7 N and pull 120.9 N at 0.7 MPa; about 20.5 kgf theoretical max at 1.0 MPa. Stroke 60 mm (standard range to 500 mm), rod 6 mm with M6x1.0 thread, M5x0.8 ports, speed 30-800 mm/s, pressure 0.15-1.0 MPa (22-145 psi).
Back both needle screws fully off, run the cylinder gently through its 60 mm stroke, then close each screw gradually until end-of-stroke bounce disappears. This keeps the variable air cushion effective without slowing mid-stroke travel.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac B06-MAC Battery-Specific Cylinder B06-MAC16X60SCM
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.