Airtac B06-MAC Battery-Specific Cylinder B06-MAC25X500SCA
The AirTAC Airtac B06-MAC Battery-Specific Cylinder B06-MAC25X500SCA is a genuine double acting + cushion standard round-body mini air cylinder with a Ø0mm bore and 500mm stroke, PT/G air ports and a stainless-steel barrel with a hard-chrome-plated rod for reliable, mildly corrosion-resistant service. A variable air cushion at both ends lets you tune end-of-stroke deceleration on site.
- BoreØ0 mm
- Stroke500 mm
- Port sizePT/G
- Acting typeDouble acting + cushion
- Rod thread
- CushionVariable air cushion, both ends
About the Airtac B06-MAC Battery-Specific Cylinder B06-MAC25X500SCA
Spanning the full 500 mm standard stroke for this bore, the MAC25X500SCA is a riveted round-body mini cylinder with double-acting power and a variable air cushion at each end. Push effort is 245 N at 0.5 MPa and 343 N at 0.7 MPa - enough to keep a long-slide pusher running with about 147 N of true working force once a sensible margin is applied.
The 10 mm hard-chrome rod slides in a stainless tube that shrugs off washdown and outdoor humidity, while rolled aluminium covers keep the assembly light and leak-tight. Needle screws at both ends trim the 30-800 mm/s speed cycle so fast or heavily loaded strokes do not hammer the covers; start with them fully open.
Airtac B06-MAC Battery-Specific Cylinder B06-MAC25X500SCA Technical Specifications
| Model | Airtac B06-MAC Battery-Specific Cylinder B06-MAC25X500SCA |
|---|---|
| Series | MAC mini cylinder |
| Bore size | Ø0 mm |
| Stroke | 500 mm |
| Acting type | Double acting + cushion |
| Port size | PT/G |
| Rod thread |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MA-series datasheet. Barrel: stainless-steel tube (round-body, riveted rolling-packed construction); piston rod: carbon steel with 20µm hard-chrome plating; covers: aluminium alloy. Thread options: PT (blank) / G / NPT. Every MA-series cylinder ships with a built-in magnet for CMSG / DMSG / EMSG position sensors.
Theoretical Output Force (Ø0mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 0 N | 0 N |
| 0.7 MPa | 0 N | 0 N |
| Max (@1.0 MPa) | 0 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac B06-MAC Battery-Specific Cylinder B06-MAC25X500SCA
| MAC | Standard round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 0 | Bore size in mm. |
| ×500 | Stroke length in mm. |
| -S | Built-in magnet for CMSG / DMSG / EMSG sensors (standard on MA series). |
| CA / U / CM | Back-cover type: CA pivot, U flat-end, CM round-end. |
MA-family variants: MA / MAC (double acting ±cushion), MSA / MTA (single acting push / pull), MAD / MACD (double rod ±cushion), MAJ / MACJ (adjustable stroke ±cushion), MAR (cushioned with integrated F/U mount). Mounting accessories: FA flange, LB foot, SDB pivot; plus I and Y knuckles. Thread PT (blank) / G / NPT.
Where the Airtac B06-MAC Battery-Specific Cylinder B06-MAC25X500SCA Is Used
Box-turn ejector
Pushes corrugated cartons through a 90 degree turning station on a packaging conveyor, cushioned ends protecting the stop face.
Carton lane sorter
Diverts cartons between two sortation lanes, the CA pivot pin allowing a hinged gate action.
Autoclave loader slide
Slides sample racks into a laboratory autoclave, where steam splash favours the stainless barrel and chrome rod.
Is the Airtac B06-MAC Battery-Specific Cylinder B06-MAC25X500SCA the Right Cylinder?
A 20 mm bore stops at 157 N push at 0.5 MPa and a 32 mm bore reaches 402 N, so the 25 mm splits the difference for 500 mm slides. Where the rod carries nothing but axial load, this stroke works as-is; for anything overhanging, add a guide or use the I or Y rod knuckle to decouple side load. Air supply comes through a 1/8" port at 0.15-1.0 MPa (22-145 psi). Unlike a locked actuator, the rod moves freely once pressure drops - fit a pilot check or rod lock if a held position matters.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) is standard for sensors
- ✓ Back cover (CA/U/CM) & mount (FA/LB/SDB)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check On first run, back off the cushion screws and release gradually.
- check Installation by qualified personnel per AirTAC docs.
Airtac B06-MAC Battery-Specific Cylinder B06-MAC25X500SCA FAQ
Push is 245.3 N and pull 206.1 N at 0.5 MPa; at 0.7 MPa expect 343.4 N push and 288.5 N pull, with about 50 kgf theoretical at 1.0 MPa. Supply 0.15-1.0 MPa (22-145 psi); the proof rating is 1.5 MPa (215 psi).
Both ends carry variable cushions: on first run, screw the needle valves fully open, then close them gradually until end-of-stroke shock disappears at your chosen speed within 30-800 mm/s. This protects the covers without acting as a brake - the piston still drifts when air is removed.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac B06-MAC Battery-Specific Cylinder B06-MAC25X500SCA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.