This model is discontinued
AirTAC has phased out the MAL series. You can still order this code here: we ship the direct replacement B06-MBL32X50CA, with the same bore, stroke, output force, port and mounting, so it fits the same application. The MBL replacement upgrades to a riveted rolling-packed body and the current CMSG / DMSG / EMSG sensor switches (the MAL used CS1-M / DS1-M).
Airtac B06-MAL Battery-Specific Pneumatic Cylinder B06-MAL32X50CA
The AirTAC B06-MAL Battery-Specific Pneumatic Cylinder B06-MAL32X50CA is a double-acting aluminum-barrel mini round cylinder with a Ø32mm bore and 50mm stroke, G1/8 air ports and a fixed rubber bumper. This model is discontinued — the direct replacement is the B06-MBL32X50CA, which matches its bore, stroke, force and mounting.
- BoreØ32 mm
- Stroke50 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- StatusDiscontinued → B06-MBL32X50CA
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac B06-MAL Battery-Specific Pneumatic Cylinder B06-MAL32X50CA
The AirTAC B06-MAL32X50CA is a discontinued double-acting aluminum mini round cylinder engineered for battery-manufacturing lines. The "B06-" prefix designates this as a battery-industry dedicated variant of the base MAL32X50CA, meaning it shares the exact same physical specs—delivering 402 N of push force at 0.5 MPa—simply optimized for cell and module assembly logistics. AirTAC replaced this legacy unit with the MBL32X50CA, a direct upgrade retaining the identical 32 mm bore, 50 mm stroke, G1/8 port, and CA pivot mounting.
This SKU features a CA clevis back cover that swings on a pin to safely absorb arcing rod movements. Unlike the legacy MAL which uses threaded front and back covers, the modern MBL body utilizes a riveted rolling-packed construction. Because this specific configuration lacks an -S magnet, it cannot accept position sensors—a limitation to note if your battery line requires end-of-stroke detection.
Airtac B06-MAL Battery-Specific Pneumatic Cylinder B06-MAL32X50CA Technical Specifications
| Model | Airtac B06-MAL Battery-Specific Pneumatic Cylinder B06-MAL32X50CA |
|---|---|
| Series | MAL aluminum-barrel mini round cylinder (discontinued) |
| Replacement | B06-MBL32X50CA |
| Bore size | Ø32 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MAL datasheet (now discontinued). The B06-MBL32X50CA carries the same ratings. Confirm against the product label before installation. Thread options: PT / G / NPT.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
The B06-MBL32X50CA produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac B06-MAL Battery-Specific Pneumatic Cylinder B06-MAL32X50CA
| MAL | Aluminum-barrel mini round cylinder, double acting (discontinued). |
|---|---|
| 32 | Bore size in mm (20/25/32/40). |
| ×50 | Stroke length in mm. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBL uses CMSG/DMSG/EMSG). |
| CA / U / CM | Back cover: CA pivot, U flat-end or CM round-end. |
Replacement mapping: MAL → MBL, MSAL → MSBL, MTAL → MTBL, MALD → MBLD, MALJ → MBLJ.
Where the Airtac B06-MAL Battery-Specific Pneumatic Cylinder B06-MAL32X50CA Is Used
Battery Cell Stacking
Pushes lithium prismatic cells into precise alignment within module trays using 402 N of force at 0.5 MPa, while the CA pivot absorbs minor misalignment during the stacking cycle.
Tab Welding Clamp
Actuates a lightweight clamping arm to hold battery busbars flat against cell terminals during laser welding, relying on the 346 N pull force to retract the jaw quickly.
Module Diverting Gate
Drives a short-stroke diverter arm on a pack assembly conveyor, using the compact 50 mm stroke to route battery modules into testing stations at speeds up to 800 mm/s.
Replacing the Airtac B06-MAL Battery-Specific Pneumatic Cylinder B06-MAL32X50CA with B06-MBL32X50CA
To replace this discontinued cylinder, order the MBL32X50CA. Confirm your 50 mm stroke, G1/8 port, PT thread form, and CA pivot back cover match the new unit. If your battery stacking fixture requires end-of-stroke feedback, you must step up to an -S magnet variant, noting that the MBL uses modern CMSG/DMSG/EMSG switches rather than the older CS1-M/DS1-M sensors. The fixed rubber bumper softens end-of-stroke impacts, but if your application needs adjustable cushioning, look to the current MBLC line.
For sizing flexibility, stepping down to the 25 mm bore yields 245 N of push force at 0.5 MPa, while stepping up to the 40 mm bore provides 628 N. A plain double-acting cylinder drifts when air pressure is lost, so if your battery handling process must hold a vertical load during an e-stop, add an external rod lock. Since this is a 50 mm stroke, the 12 mm rod is highly tolerant of direct axial loads without needing external guides.
Upgrade checklist
- ✓ Order the B06-MBL32X50CA (same bore/stroke/force)
- ✓ Same G1/8 port and mounting accessories
- ✓ Sensor: swap CS1-M/DS1-M → CMSG/DMSG/EMSG
- ✓ Need a cushion? use MBLC (adjustable air cushion)
- ✓ Confirm back cover (CA / U) and thread (PT/NPT/G)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.1 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Front/rear covers are threaded — not intended for field disassembly.
- check Use the correct mounting accessory (LB / FA / SDB) and back cover (CA / U / CM).
- check For new builds, specify the B06-MBL32X50CA instead of this discontinued model.
Airtac B06-MAL Battery-Specific Pneumatic Cylinder B06-MAL32X50CA FAQ
Yes, the B06-MAL32X50CA is discontinued. The direct replacement is the MBL32X50CA, which matches the 32 mm bore, 50 mm stroke, G1/8 port, and CA pivot mounting. The B06- prefix simply marked it for battery manufacturing; the MBL replacement serves the same role with an upgraded riveted body.
At 0.5 MPa, it provides 402 N push and 346 N pull force. At 0.7 MPa, push increases to 563 N, with a theoretical maximum of 82 kgf at 1.0 MPa. Because this specific SKU lacks an -S magnet, it cannot accept position sensors; adding a magnet to the MBL replacement requires modern CMSG/DMSG/EMSG switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
Direct Upgrade
The B06-MBL32X50CA replaces this model 1:1.
Fast Dispatch
MBL replacements are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Recommended AirTAC MBL Replacements
Request a Quote (Airtac B06-MAL Battery-Specific Pneumatic Cylinder B06-MAL32X50CA → B06-MBL32X50CA)
Tell us the quantity and destination — we quote the direct B06-MBL32X50CA replacement with price, stock and lead time, usually within 7-8 hours.