This model is discontinued
AirTAC has phased out the MAL series. The drop-in replacement is MBL40X5CA — same bore, stroke, output force, port and mounting, so it fits the same application. Simply order the MBL40X5CA in place of this model. The MBL replacement upgrades to a riveted rolling-packed body and the current CMSG / DMSG / EMSG sensor switches (the MAL used CS1-M / DS1-M).
The AirTAC AirTAC MAL40X5CA (Discontinued) → MBL40X5CA is a double-acting aluminum-barrel mini round cylinder with a Ø40mm bore and 5mm stroke, G1/4 air ports and a fixed rubber bumper. This model is discontinued — the drop-in replacement is the MBL40X5CA, which matches its bore, stroke, force and mounting.
The AirTAC MAL40X5CA is a discontinued double-acting aluminum mini round cylinder. Built for compact spaces, this 40mm bore unit delivers 628N of push force and 528N of pull force at 0.5 MPa, peaking at a 128kgf maximum. AirTAC replaced it with the MBL40X5CA, a drop-in alternative retaining the exact same bore, stroke, port, and CA pivot mounting.
This legacy model features a threaded front and back cover, whereas the modern MBL uses a riveted rolling-packed body. Because this specific SKU lacks an -S magnet, it cannot accept a position sensor. The internal piston relies on a heterogeneous two-way seal that retains grease, paired with a self-lubricating front-cover bearing guide.
| Model | AirTAC MAL40X5CA (Discontinued) → MBL40X5CA |
|---|---|
| Series | MAL aluminum-barrel mini round cylinder (discontinued) |
| Replacement | MBL40X5CA |
| Bore size | Ø40 mm |
| Stroke | 5 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MAL datasheet (now discontinued). The MBL40X5CA carries the same ratings. Confirm against the product label before installation. Thread options: PT / G / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
The MBL40X5CA produces the same force from the same bore — a true drop-in on output. Actual usable force is lower than theoretical; size with a margin.
| MAL | Aluminum-barrel mini round cylinder, double acting (discontinued). |
|---|---|
| 40 | Bore size in mm (20/25/32/40). |
| ×5 | Stroke length in mm. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBL uses CMSG/DMSG/EMSG). |
| CA / U / CM | Back cover: CA pivot, U flat-end or CM round-end. |
Replacement mapping: MAL → MBL, MSAL → MSBL, MTAL → MTBL, MALD → MBLD, MALJ → MBLJ.
Uses the 5mm stroke and 628N push force to rapidly kick small cartons off a conveyor belt into a packing chute without occupying much longitudinal space.
Provides a short, forceful 880N at 0.7 MPa to eject small stamped metal pins from a die plate, leveraging the CA pivot to absorb slight angular misalignment.
Actuates a lightweight holding brake on an automated storage crane, where the fixed rubber bumper adequately softens the abrupt 5mm end-of-stroke impact.
To replace the MAL40X5CA, order the MBL40X5CA. Verify your setup retains the PT tapered port thread, the 16mm carbon-steel rod with 20um hard chrome plating, and the CA pivot back cover, which swings on a pin to accommodate arcing loads. If your mechanism requires end-of-stroke cushioning, note that this legacy unit only has a fixed rubber bumper; you will need to step up to the current-line MBLC for an adjustable air cushion.
For sizing flexibility, stepping down to the 32mm bore yields 402N of push force at 0.5 MPa, while stepping up is not available as 40mm is the largest mini round bore. Remember that a plain cylinder does not hold its position when air is lost; the rod drifts. For suspended loads, install an external rod lock or a pilot-operated check valve.
Upgrade checklist
Yes, the MAL40X5CA is discontinued. The exact drop-in replacement is the MBL40X5CA, which matches the 40mm bore, 5mm stroke, 628N force, G1/4 port, and CA pivot mounting. The main upgrade is a riveted rolling-packed body replacing the original threaded covers.
At 0.5 MPa, it pushes with 628N and pulls with 528N. At 0.7 MPa, push increases to 880N, with a theoretical max of 128kgf at 1.0 MPa. Because this SKU lacks the -S magnet, it cannot accept CS1-M or DS1-M position sensors; the MBL replacement uses CMSG, DMSG, or EMSG switches.
Genuine AirTAC parts produced by AirTAC factory.
The MBL40X5CA replaces this model 1:1.
MBL replacements usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Tell us the quantity and destination — we quote the drop-in MBL40X5CA replacement with price, stock and lead time, usually within 7-8 hours.