This model is discontinued
AirTAC has phased out the MAL series. The drop-in replacement is MBL40X60SCA — same bore, stroke, output force, port and mounting, so it fits the same application. Simply order the MBL40X60SCA in place of this model. The MBL replacement upgrades to a riveted rolling-packed body and the current CMSG / DMSG / EMSG sensor switches (the MAL used CS1-M / DS1-M).
The AirTAC AirTAC MAL40X60SCA (Discontinued) -> MBL40X60SCA is a double-acting aluminum-barrel mini round cylinder with a Ø40mm bore and 60mm stroke, G1/4 air ports and a fixed rubber bumper. This model is discontinued — the drop-in replacement is the MBL40X60SCA, which matches its bore, stroke, force and mounting.
The AirTAC MAL40X60SCA is a discontinued double-acting aluminum mini round cylinder delivering 628 N of push force at 0.5 MPa. The exact drop-in replacement is the MBL40X60SCA, which matches the 40 mm bore, 60 mm stroke, G1/4 port, and CA pivot mounting. The legacy MAL body uses threaded front and back covers, whereas the current MBL features a riveted rolling-packed body for equally robust performance.
This specific SKU includes a built-in magnet (-S) and a CA pivot clevis. The magnet on the MAL works with older CS1-M or DS1-M reed switches, but upgrading to the MBL means transitioning to the modern CMSG, DMSG, or EMSG sensor families. The piston relies on a heterogeneous two-way seal that retains grease, and the carbon-steel rod has a 20 um hard-chrome plating to resist wear.
| Model | AirTAC MAL40X60SCA (Discontinued) -> MBL40X60SCA |
|---|---|
| Series | MAL aluminum-barrel mini round cylinder (discontinued) |
| Replacement | MBL40X60SCA |
| Bore size | Ø40 mm |
| Stroke | 60 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MAL datasheet (now discontinued). The MBL40X60SCA carries the same ratings. Confirm against the product label before installation. Thread options: PT / G / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
The MBL40X60SCA produces the same force from the same bore — a true drop-in on output. Actual usable force is lower than theoretical; size with a margin.
| MAL | Aluminum-barrel mini round cylinder, double acting (discontinued). |
|---|---|
| 40 | Bore size in mm (20/25/32/40). |
| ×60 | Stroke length in mm. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBL uses CMSG/DMSG/EMSG). |
| CA / U / CM | Back cover: CA pivot, U flat-end or CM round-end. |
Replacement mapping: MAL → MBL, MSAL → MSBL, MTAL → MTBL, MALD → MBLD, MALJ → MBLJ.
Drives a small marking die with 628 N of push force at 0.5 MPa, securely stamping serial numbers into soft aluminum tags.
Uses the 60 mm stroke to extend a routing flap on a packaging line, redirecting cartons at high speed without lateral binding.
Lifts loaded product trays using the CA pivot clevis to absorb arcing loads during vertical transfer movements.
To replace the MAL40X60SCA, order the MBL40X60SCA and verify your CA pivot pin and G1/4 PT air lines. Because this SKU has the -S magnet, you must swap your legacy CS1-M or DS1-M switches for CMSG, DMSG, or EMSG sensors. If your application requires adjustable end-of-stroke cushioning, step up to the MBLC variant, as the MAL only provides a fixed rubber bumper. If 628 N of push at 0.5 MPa is excessive, step down to the 32 mm bore (402 N push); if you need more power, note that 40 mm is the largest available mini round body in this family. A plain bumper does not hold position, so add an external rod lock for fail-safe load holding.
Upgrade checklist
Yes, the MAL40X60SCA is discontinued. The exact drop-in replacement is the MBL40X60SCA, which matches the 40 mm bore, 60 mm stroke, G1/4 port, and CA pivot mounting. You must upgrade your -S magnet sensors from the older CS1-M or DS1-M to the current CMSG, DMSG, or EMSG switches.
The 40 mm bore provides a push force of 628 N and a pull force of 528 N at 0.5 MPa. At 0.7 MPa, the push force increases to 880 N. The maximum theoretical force is 128 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
The MBL40X60SCA replaces this model 1:1.
MBL replacements usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Tell us the quantity and destination — we quote the drop-in MBL40X60SCA replacement with price, stock and lead time, usually within 7-8 hours.