This model is discontinued
AirTAC has phased out the MAL series. The drop-in replacement is MBL40X63CA — same bore, stroke, output force, port and mounting, so it fits the same application. Simply order the MBL40X63CA in place of this model. The MBL replacement upgrades to a riveted rolling-packed body and the current CMSG / DMSG / EMSG sensor switches (the MAL used CS1-M / DS1-M).
The AirTAC AirTAC MAL40X63CA (Discontinued) -> MBL40X63CA is a double-acting aluminum-barrel mini round cylinder with a Ø40mm bore and 63mm stroke, G1/4 air ports and a fixed rubber bumper. This model is discontinued — the drop-in replacement is the MBL40X63CA, which matches its bore, stroke, force and mounting.
The AirTAC MAL40X63CA is a discontinued double-acting aluminum mini round cylinder featuring a 40mm bore and 63mm stroke. It delivers 628N push and 528N pull at 0.5MPa, utilizing a G1/4 port and an M12x1.25 rod thread. The exact drop-in replacement is the MBL40X63CA, matching the original force, port, and CA pivot mounting for a seamless swap.
This legacy unit uses threaded front and back covers, whereas the modern MBL upgrade employs a riveted rolling-packed body. The CA back cover acts as a pivot clevis, swinging on a pin to absorb arcing loads. Because this specific SKU lacks an -S magnet, it cannot accept a position sensor. The internal heterogeneous two-way seal retains grease, and the carbon-steel rod features 20um hard-chrome plating to resist wear.
| Model | AirTAC MAL40X63CA (Discontinued) -> MBL40X63CA |
|---|---|
| Series | MAL aluminum-barrel mini round cylinder (discontinued) |
| Replacement | MBL40X63CA |
| Bore size | Ø40 mm |
| Stroke | 63 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MAL datasheet (now discontinued). The MBL40X63CA carries the same ratings. Confirm against the product label before installation. Thread options: PT / G / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
The MBL40X63CA produces the same force from the same bore — a true drop-in on output. Actual usable force is lower than theoretical; size with a margin.
| MAL | Aluminum-barrel mini round cylinder, double acting (discontinued). |
|---|---|
| 40 | Bore size in mm (20/25/32/40). |
| ×63 | Stroke length in mm. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBL uses CMSG/DMSG/EMSG). |
| CA / U / CM | Back cover: CA pivot, U flat-end or CM round-end. |
Replacement mapping: MAL → MBL, MSAL → MSBL, MTAL → MTBL, MALD → MBLD, MALJ → MBLJ.
Drives a swinging diverter gate on a packaging conveyor, utilizing the 628N push force at 0.5MPa to redirect heavy cardboard cartons.
Actuates a heavy safety door via the CA pivot clevis, allowing the rod to swing naturally without bending as the panel arcs open.
Indexes wooden pallets into a stacking chute, relying on the 880N thrust at 0.7MPa to overcome sliding friction.
To replace the MAL40X63CA, order the MBL40X63CA, ensuring you keep the 40mm bore, 63mm stroke, G1/4 port, PT thread, and CA pivot back cover. If you need to adjust the force, the next size down is the 32mm bore (delivering 402N push at 0.5MPa), and the next size up is the 50mm bore (confirm exact force from the MBL50 datasheet).
If your application requires an adjustable air cushion instead of the fixed rubber bumper found on this MAL, step up to the current MBLC line. Since this SKU has no -S magnet, you cannot mount a sensor; if position detection is needed, order an MBL40X63CAS and note that the modern MBL uses CMSG/DMSG/EMSG switches rather than the older CS1-M/DS1-M family. A plain bumper does not lock the rod, so add an external rod lock if the load must be held during air loss.
Upgrade checklist
Yes, the MAL40X63CA is discontinued. The exact drop-in replacement is the MBL40X63CA, offering the same 40mm bore, 63mm stroke, 628N force, G1/4 port, and CA pivot mounting. The MBL upgrades the body to a riveted rolling-packed design.
The 40mm bore provides a push force of 628N and a pull force of 528N at 0.5MPa. At 0.7MPa, the push force is 880N, with a maximum theoretical force of 128kgf at 1.0MPa. It uses a G1/4 port and an M12x1.25 rod thread.
Genuine AirTAC parts produced by AirTAC factory.
The MBL40X63CA replaces this model 1:1.
MBL replacements usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Tell us the quantity and destination — we quote the drop-in MBL40X63CA replacement with price, stock and lead time, usually within 7-8 hours.