This model is discontinued
AirTAC has phased out the MAL series. The drop-in replacement is MBL40X8CA — same bore, stroke, output force, port and mounting, so it fits the same application. Simply order the MBL40X8CA in place of this model. The MBL replacement upgrades to a riveted rolling-packed body and the current CMSG / DMSG / EMSG sensor switches (the MAL used CS1-M / DS1-M).
The AirTAC AirTAC MAL40X8CA (Discontinued) → MBL40X8CA is a double-acting aluminum-barrel mini round cylinder with a Ø40mm bore and 8mm stroke, G1/4 air ports and a fixed rubber bumper. This model is discontinued — the drop-in replacement is the MBL40X8CA, which matches its bore, stroke, force and mounting.
The AirTAC MAL40X8CA is a discontinued double-acting aluminum mini round cylinder. As the largest bore in this legacy range, it delivers a robust 628 N push force at 0.5 MPa. AirTAC replaced this unit with the MBL40X8CA, a drop-in substitute retaining the exact 40mm bore, 8mm stroke, 128 kgf maximum force, G1/4 port, and CA pivot mounting.
This specific SKU features a CA clevis back cover that swings on a pin to absorb arcing motion. Because it lacks the -S option, it cannot accept a position sensor. The original MAL body used threaded front and back covers, whereas the current MBL upgrade features a riveted rolling-packed body for greater structural integrity.
| Model | AirTAC MAL40X8CA (Discontinued) → MBL40X8CA |
|---|---|
| Series | MAL aluminum-barrel mini round cylinder (discontinued) |
| Replacement | MBL40X8CA |
| Bore size | Ø40 mm |
| Stroke | 8 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MAL datasheet (now discontinued). The MBL40X8CA carries the same ratings. Confirm against the product label before installation. Thread options: PT / G / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
The MBL40X8CA produces the same force from the same bore — a true drop-in on output. Actual usable force is lower than theoretical; size with a margin.
| MAL | Aluminum-barrel mini round cylinder, double acting (discontinued). |
|---|---|
| 40 | Bore size in mm (20/25/32/40). |
| ×8 | Stroke length in mm. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBL uses CMSG/DMSG/EMSG). |
| CA / U / CM | Back cover: CA pivot, U flat-end or CM round-end. |
Replacement mapping: MAL → MBL, MSAL → MSBL, MTAL → MTBL, MALD → MBLD, MALJ → MBLJ.
Delivers 628 N of push at 0.5 MPa to knock small metal stamped parts out of a die in a tight mechanical clearance zone.
Uses the CA clevis back cover to swing a diverter arm on a packaging conveyor, safely absorbing the side-load arc during product routing.
Provides a short 8mm stroke to hold rigid electronic test fixtures firmly in place without overtraveling and damaging delicate components.
To replace the MAL40X8CA, order the MBL40X8CA and verify your PT thread port and CA pivot bracket. If your cycle creates arcing loads, the CA clevis is essential; for rigid straight-line pushes, switch to a U flat-end cover. If you need position sensing, note that this non-S SKU cannot mount a sensor, and upgrading to an MBL with an S code changes the switch family from the legacy CS1-M/DS1-M to the modern CMSG/DMSG/EMSG.
For sizing flexibility, stepping down to the 32mm bore drops the 0.5 MPa push force to 402 N, while no larger standard bore exists in this mini series. The fixed rubber bumper softens the 8mm stroke end, but it is not a lock; if you must hold a load during air loss, add an external rod lock. The MAL lacks adjustable cushioning, so if shock absorption is critical, specify the current-line MBLC.
Upgrade checklist
Yes, the MAL40X8CA is discontinued. The exact drop-in replacement is the MBL40X8CA, which shares the same 40mm bore, 8mm stroke, G1/4 port, and CA pivot mounting. You simply order the MBL equivalent for a direct fit.
The MAL40X8CA generates 628 N push and 528 N pull at 0.5 MPa, 880 N push at 0.7 MPa, and a maximum 128 kgf at 1.0 MPa. It uses a fixed rubber bumper that softens the stroke end but does not lock; the rod will drift if air pressure is lost.
Genuine AirTAC parts produced by AirTAC factory.
The MBL40X8CA replaces this model 1:1.
MBL replacements usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Tell us the quantity and destination — we quote the drop-in MBL40X8CA replacement with price, stock and lead time, usually within 7-8 hours.