This model is discontinued
AirTAC has phased out the MALJ series. You can still order this code here: we ship the direct replacement MBLJ20X125-20S, with the same bore, stroke, output force, port and mounting, so it fits the same application. The MBLJ replacement upgrades to a riveted rolling-packed body and CMSG / DMSG / EMSG sensors (the MAL used CS1-M / DS1-M).
Airtac MALJ20 Adjustable Mini Cylinder MALJ20X125-20-S
The AirTAC Airtac MALJ20 Adjustable Mini Cylinder MALJ20X125-20-S is a double-acting aluminum mini cylinder with a rear adjustable-stroke stopper: you can trim up to 20 mm, giving a usable end-position window from 105 to 125 mm. This model is discontinued — the direct replacement is the MBLJ20X125-20-S.
- BoreØ20 mm
- Stroke125 mm
- Adjust window105–125 mm
- Port sizeG1/8
- Rod threadM8×1.25
- StatusDiscontinued → MBLJ20X125-20-S
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MALJ20 Adjustable Mini Cylinder MALJ20X125-20-S
The AirTAC MALJ20X125-20-S is a discontinued double-acting double-rod cylinder with a 20mm bore and 125mm stroke. A rear screw lets you trim up to 20mm, giving a usable window of 105-125mm to fine-tune reach. The direct replacement is the MBLJ20X125-20-S.
This bore 20 unit uses an M8x1.25 rod, a G1/8 PT port, and a fixed rubber bumper. The -S magnet works with CS1-M/DS1-M switches; the MBLJ upgrades to CMSG/DMSG/EMSG. The original MALJ has threaded covers, while the MBLJ uses a riveted rolling-packed body. Remember the adjuster is a travel stop, not a lock; it cannot hold a load without live air.
Airtac MALJ20 Adjustable Mini Cylinder MALJ20X125-20-S Technical Specifications
| Model | Airtac MALJ20 Adjustable Mini Cylinder MALJ20X125-20-S |
|---|---|
| Series | MALJ adjustable-stroke mini cylinder (discontinued) |
| Replacement | MBLJ20X125-20-S |
| Bore size | Ø20 mm |
| Stroke | 125 mm |
| Adjustable window | 105 – 125 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | G1/8 |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 300 mm |
The rear adjuster is a travel stop, not a lock — it sets the end position but does not hold the load without live air. No back-cover code and no SDB on adjustable-stroke. The MBLJ20X125-20-S carries the same ratings.
Theoretical Output Force (Ø20mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 132 N | 132 N |
| 0.7 MPa | 185 N | — |
| Max (@1.0 MPa) | 27 kgf | |
MALJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod MAL push of the same bore. The MBLJ20X125-20-S matches these values.
Model Code: Airtac MALJ20 Adjustable Mini Cylinder MALJ20X125-20-S
| MALJ | Adjustable-stroke aluminum mini cylinder, double acting (discontinued). |
|---|---|
| 20 | Bore size in mm (20/25/32/40). |
| ×125 | Nominal stroke length in mm. |
| -20 | Adjustable amount: trim the end to a 105–125 mm window. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBLJ uses CMSG/DMSG/EMSG). |
Replacement: MALJ → MBLJ. No back-cover (CA/U/CM) and no SDB. Mounting: FA / LB.
Where the Airtac MALJ20 Adjustable Mini Cylinder MALJ20X125-20-S Is Used
Dispenser Nozzle Height
Trims the extension window on an adhesive dispensing robot to prevent the nozzle from crashing into a populated circuit board before the cycle starts.
Light Parts Ejector
Pushes small plastic clips out of an injection mold cavity, using the 20mm adjustment to tune the ejection distance for varying part thicknesses.
Replacing the Airtac MALJ20 Adjustable Mini Cylinder MALJ20X125-20-S with MBLJ20X125-20-S
To replace this MALJ20X125-20-S, install the direct replacement MBLJ20X125-20-S. Confirm the 20mm bore, 125mm stroke, 20mm adjust code, G1/8 port, PT thread, and FA/LB mounting (no back cover or SDB). The -S magnet means a sensor family change from CS1-M/DS1-M to CMSG/DMSG/EMSG. The rear adjuster sets end position but is not a lock.
At 125mm stroke, watch rod-bending side loads on the 8mm rod.
Upgrade checklist
- ✓ Order the MBLJ20X125-20-S (same bore/stroke/adjust)
- ✓ Same 105–125 mm adjustable window
- ✓ Adjuster is a stop, not a lock
- ✓ No back cover / SDB — plan an FA/LB mount
- ✓ Sensor: swap CS1-M/DS1-M → CMSG/DMSG/EMSG
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.1 – 1.0 MPa operating pressure.
- check The rear adjuster sets the end position — it is not a load lock.
- check No back-cover / SDB on adjustable-stroke — use FA / LB.
- check Front/rear covers are threaded — not for field disassembly.
- check For new builds, specify the MBLJ20X125-20-S instead of this discontinued model.
Airtac MALJ20 Adjustable Mini Cylinder MALJ20X125-20-S FAQ
Yes, the MALJ20X125-20-S is discontinued. The direct replacement is the MBLJ20X125-20-S, which matches the 20mm bore, 125mm stroke, 20mm adjust code, G1/8 port, and force. The MBLJ upgrades the threaded covers to a riveted rolling-packed body and changes the -S magnet switches from CS1-M/DS1-M to CMSG/DMSG/EMSG.
The 20mm adjuster is a travel stop that lets you shorten the end position, creating a usable stroke window of 105-125mm. It is not a lock and cannot hold a load without live air.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
Direct Upgrade
The MBLJ20X125-20-S replaces this model 1:1.
Fast Dispatch
MBLJ replacements are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Recommended AirTAC MBLJ Replacements
Request a Quote (Airtac MALJ20 Adjustable Mini Cylinder MALJ20X125-20-S → MBLJ20X125-20-S)
Tell us the quantity and destination — we quote the direct MBLJ20X125-20-S replacement with price, stock and lead time, usually within 7-8 hours.