This model is discontinued
AirTAC has phased out the MALJ series. You can still order this code here: we ship the direct replacement MBLJ32X100-100, with the same bore, stroke, output force, port and mounting, so it fits the same application. The MBLJ replacement upgrades to a riveted rolling-packed body and CMSG / DMSG / EMSG sensors (the MAL used CS1-M / DS1-M).
Airtac MALJ32 Adjustable Mini Cylinder MALJ32X100-100
The AirTAC Airtac MALJ32 Adjustable Mini Cylinder MALJ32X100-100 is a double-acting aluminum mini cylinder with a rear adjustable-stroke stopper: you can trim up to 100 mm, giving a usable end-position window from 0 to 100 mm. This model is discontinued — the direct replacement is the MBLJ32X100-100.
- BoreØ32 mm
- Stroke100 mm
- Adjust window0–100 mm
- Port sizeG1/8
- Rod threadM10×1.25
- StatusDiscontinued → MBLJ32X100-100
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MALJ32 Adjustable Mini Cylinder MALJ32X100-100
The AirTAC MALJ32X100-100 is a discontinued double-acting mini cylinder with a 32 mm bore, 100 mm stroke, and a 100 mm rear adjuster. This yields a usable end-position window of 0-100 mm. The direct replacement is the MBLJ32X100-100, matching bore, stroke, port, and force.
This SKU has no magnet (-S), so it cannot accept a position sensor. It uses a fixed rubber bumper, not an adjustable air cushion. The rear adjuster is a travel stop for dialling in reach, not a lock for holding loads without live air. Upgrade details: the MALJ uses threaded covers and CS1-M/DS1-M sensors, while the MBLJ32X100-100 features a riveted rolling-packed body and CMSG/DMSG/EMSG switches.
Airtac MALJ32 Adjustable Mini Cylinder MALJ32X100-100 Technical Specifications
| Model | Airtac MALJ32 Adjustable Mini Cylinder MALJ32X100-100 |
|---|---|
| Series | MALJ adjustable-stroke mini cylinder (discontinued) |
| Replacement | MBLJ32X100-100 |
| Bore size | Ø32 mm |
| Stroke | 100 mm |
| Adjustable window | 0 – 100 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
The rear adjuster is a travel stop, not a lock — it sets the end position but does not hold the load without live air. No back-cover code and no SDB on adjustable-stroke. The MBLJ32X100-100 carries the same ratings.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
MALJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod MAL push of the same bore. The MBLJ32X100-100 matches these values.
Model Code: Airtac MALJ32 Adjustable Mini Cylinder MALJ32X100-100
| MALJ | Adjustable-stroke aluminum mini cylinder, double acting (discontinued). |
|---|---|
| 32 | Bore size in mm (20/25/32/40). |
| ×100 | Nominal stroke length in mm. |
| -100 | Adjustable amount: trim the end to a 0–100 mm window. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBLJ uses CMSG/DMSG/EMSG). |
Replacement: MALJ → MBLJ. No back-cover (CA/U/CM) and no SDB. Mounting: FA / LB.
Where the Airtac MALJ32 Adjustable Mini Cylinder MALJ32X100-100 Is Used
Connector Insertion Press
Fine-tune the insertion reach for ribbon connectors, relying on the 346 N pull to retract the tool safely after seating the part.
Replacing the Airtac MALJ32 Adjustable Mini Cylinder MALJ32X100-100 with MBLJ32X100-100
To replace the MALJ32X100-100, order the direct replacement MBLJ32X100-100. Confirm the 32 mm bore, 100 mm stroke, 100 mm adjust code, G1/8 port, PT thread, and FA/LB mounting (no back cover or SDB). Since this SKU lacks a magnet, you cannot fit a sensor; if you need sensing, the MBLJ replacement requires CMSG/DMSG/EMSG switches.
Remember the rear adjuster is a stop, not a lock; use an external lock for held loads.
Upgrade checklist
- ✓ Order the MBLJ32X100-100 (same bore/stroke/adjust)
- ✓ Same 0–100 mm adjustable window
- ✓ Adjuster is a stop, not a lock
- ✓ No back cover / SDB — plan an FA/LB mount
- ✓ Sensor: swap CS1-M/DS1-M → CMSG/DMSG/EMSG
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.1 – 1.0 MPa operating pressure.
- check The rear adjuster sets the end position — it is not a load lock.
- check No back-cover / SDB on adjustable-stroke — use FA / LB.
- check Front/rear covers are threaded — not for field disassembly.
- check For new builds, specify the MBLJ32X100-100 instead of this discontinued model.
Airtac MALJ32 Adjustable Mini Cylinder MALJ32X100-100 FAQ
Yes, the MALJ32X100-100 is discontinued. The direct replacement is the MBLJ32X100-100, matching the 32 mm bore, 100 mm stroke, 100 mm adjust code, G1/8 port, and mounting. The MBLJ upgrades to a riveted rolling-packed body and CMSG/DMSG/EMSG sensors.
The 100 mm adjust code creates a usable end-position window of 0-100 mm. The adjuster is a travel stop, not a lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
Direct Upgrade
The MBLJ32X100-100 replaces this model 1:1.
Fast Dispatch
MBLJ replacements are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Recommended AirTAC MBLJ Replacements
Request a Quote (Airtac MALJ32 Adjustable Mini Cylinder MALJ32X100-100 → MBLJ32X100-100)
Tell us the quantity and destination — we quote the direct MBLJ32X100-100 replacement with price, stock and lead time, usually within 7-8 hours.