This model is discontinued
AirTAC has phased out the MALJ series. You can still order this code here: we ship the direct replacement MBLJ32X175-30, with the same bore, stroke, output force, port and mounting, so it fits the same application. The MBLJ replacement upgrades to a riveted rolling-packed body and CMSG / DMSG / EMSG sensors (the MAL used CS1-M / DS1-M).
Airtac MALJ32 Adjustable Mini Cylinder MALJ32X175-30
The AirTAC Airtac MALJ32 Adjustable Mini Cylinder MALJ32X175-30 is a double-acting aluminum mini cylinder with a rear adjustable-stroke stopper: you can trim up to 30 mm, giving a usable end-position window from 145 to 175 mm. This model is discontinued — the direct replacement is the MBLJ32X175-30.
- BoreØ32 mm
- Stroke175 mm
- Adjust window145–175 mm
- Port sizeG1/8
- Rod threadM10×1.25
- StatusDiscontinued → MBLJ32X175-30
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MALJ32 Adjustable Mini Cylinder MALJ32X175-30
The AirTAC MALJ32X175-30 is a discontinued double-acting, double-rod mini cylinder with a 32mm bore and 175mm stroke. A rear stopper lets you trim up to 30mm, giving a usable end-position window of 145-175mm. The direct replacement is the MBLJ32X175-30, matching bore, stroke, port, and force.
This SKU has no magnet (-S), so it cannot accept a position sensor. The adjuster sets travel but does not hold load without live air. The fixed rubber bumper softens end impact. Unlike the threaded covers on this MALJ, the MBLJ replacement uses a riveted rolling-packed body for greater structural integrity.
Airtac MALJ32 Adjustable Mini Cylinder MALJ32X175-30 Technical Specifications
| Model | Airtac MALJ32 Adjustable Mini Cylinder MALJ32X175-30 |
|---|---|
| Series | MALJ adjustable-stroke mini cylinder (discontinued) |
| Replacement | MBLJ32X175-30 |
| Bore size | Ø32 mm |
| Stroke | 175 mm |
| Adjustable window | 145 – 175 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
The rear adjuster is a travel stop, not a lock — it sets the end position but does not hold the load without live air. No back-cover code and no SDB on adjustable-stroke. The MBLJ32X175-30 carries the same ratings.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
MALJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod MAL push of the same bore. The MBLJ32X175-30 matches these values.
Model Code: Airtac MALJ32 Adjustable Mini Cylinder MALJ32X175-30
| MALJ | Adjustable-stroke aluminum mini cylinder, double acting (discontinued). |
|---|---|
| 32 | Bore size in mm (20/25/32/40). |
| ×175 | Nominal stroke length in mm. |
| -30 | Adjustable amount: trim the end to a 145–175 mm window. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBLJ uses CMSG/DMSG/EMSG). |
Replacement: MALJ → MBLJ. No back-cover (CA/U/CM) and no SDB. Mounting: FA / LB.
Where the Airtac MALJ32 Adjustable Mini Cylinder MALJ32X175-30 Is Used
Textile Guide Tensioning
Fine-tune the end position of a fabric guide arm in a weaving loom, trimming 30mm at the rear to adjust material tension dynamically during runs.
Small Parts Ejector
Eject stamped metal parts from a die set, using the 346N pull force to retract the pin and the rear stopper to dial the exact rest position.
Replacing the Airtac MALJ32 Adjustable Mini Cylinder MALJ32X175-30 with MBLJ32X175-30
Replace this MALJ32X175-30 directly with the MBLJ32X175-30. Confirm the 32mm bore, 175mm stroke, 30mm adjust code, G1/8 port, and PT thread. Mounting is Basic, FA, or LB only (no back cover or SDB). Because this SKU lacks the -S magnet, it cannot take a sensor; if you need sensing, the MBLJ equivalent uses CMSG/DMSG/EMSG switches instead of the older CS1-M/DS1-M. Remember the adjuster is a stop, not a lock.
At 175mm stroke, keep side-load minimized to avoid rod bending.
Upgrade checklist
- ✓ Order the MBLJ32X175-30 (same bore/stroke/adjust)
- ✓ Same 145–175 mm adjustable window
- ✓ Adjuster is a stop, not a lock
- ✓ No back cover / SDB — plan an FA/LB mount
- ✓ Sensor: swap CS1-M/DS1-M → CMSG/DMSG/EMSG
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.1 – 1.0 MPa operating pressure.
- check The rear adjuster sets the end position — it is not a load lock.
- check No back-cover / SDB on adjustable-stroke — use FA / LB.
- check Front/rear covers are threaded — not for field disassembly.
- check For new builds, specify the MBLJ32X175-30 instead of this discontinued model.
Airtac MALJ32 Adjustable Mini Cylinder MALJ32X175-30 FAQ
Yes, the MALJ32X175-30 is discontinued. The direct replacement is the MBLJ32X175-30, matching the 32mm bore, 175mm stroke, 30mm adjust code, G1/8 port, and mounting. The MBLJ upgrades the body to a riveted rolling-packed design.
The 30mm adjust code lets you trim the rear position, creating a usable stroke window of 145-175mm. The adjuster is a travel stop, not a lock. This no-S SKU cannot take a sensor.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
Direct Upgrade
The MBLJ32X175-30 replaces this model 1:1.
Fast Dispatch
MBLJ replacements are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Recommended AirTAC MBLJ Replacements
Request a Quote (Airtac MALJ32 Adjustable Mini Cylinder MALJ32X175-30 → MBLJ32X175-30)
Tell us the quantity and destination — we quote the direct MBLJ32X175-30 replacement with price, stock and lead time, usually within 7-8 hours.