This model is discontinued
AirTAC has phased out the MALJ series. You can still order this code here: we ship the direct replacement MBLJ32X250-10, with the same bore, stroke, output force, port and mounting, so it fits the same application. The MBLJ replacement upgrades to a riveted rolling-packed body and CMSG / DMSG / EMSG sensors (the MAL used CS1-M / DS1-M).
Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-10
The AirTAC Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-10 is a double-acting aluminum mini cylinder with a rear adjustable-stroke stopper: you can trim up to 10 mm, giving a usable end-position window from 240 to 250 mm. This model is discontinued — the direct replacement is the MBLJ32X250-10.
- BoreØ32 mm
- Stroke250 mm
- Adjust window240–250 mm
- Port sizeG1/8
- Rod threadM10×1.25
- StatusDiscontinued → MBLJ32X250-10
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-10
The AirTAC MALJ32X250-10 is a discontinued double-acting double-rod cylinder with a 32 mm bore and a 10 mm rear stroke adjuster. This gives a usable extension window of 240-250 mm. The direct replacement is the MBLJ32X250-10, matching the bore, stroke, adjust code, and G1/8 port.
This SKU lacks a magnet (-S), so it cannot accept a position sensor. The rear adjuster is a travel stop, not a lock; it sets the end position but will not hold a load without live air. The MALJ uses a fixed rubber bumper and threaded covers, whereas the MBLJ upgrade features a riveted rolling-packed body.
Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-10 Technical Specifications
| Model | Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-10 |
|---|---|
| Series | MALJ adjustable-stroke mini cylinder (discontinued) |
| Replacement | MBLJ32X250-10 |
| Bore size | Ø32 mm |
| Stroke | 250 mm |
| Adjustable window | 240 – 250 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
The rear adjuster is a travel stop, not a lock — it sets the end position but does not hold the load without live air. No back-cover code and no SDB on adjustable-stroke. The MBLJ32X250-10 carries the same ratings.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
MALJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod MAL push of the same bore. The MBLJ32X250-10 matches these values.
Model Code: Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-10
| MALJ | Adjustable-stroke aluminum mini cylinder, double acting (discontinued). |
|---|---|
| 32 | Bore size in mm (20/25/32/40). |
| ×250 | Nominal stroke length in mm. |
| -10 | Adjustable amount: trim the end to a 240–250 mm window. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBLJ uses CMSG/DMSG/EMSG). |
Replacement: MALJ → MBLJ. No back-cover (CA/U/CM) and no SDB. Mounting: FA / LB.
Where the Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-10 Is Used
Aluminum Extrusion Saw
Trims the cut-off stroke by 10 mm to clear the blade guard, relying on the fixed rubber bumper to soften the 563 N impact at 0.7 MPa.
Carton Flap Folder
Fine-tunes the 250 mm reach to fold varying box heights without swapping hardware, using 346 N pull force to retract the arm.
Replacing the Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-10 with MBLJ32X250-10
To replace this MALJ32X250-10, order the MBLJ32X250-10. Confirm the 32 mm bore, 250 mm stroke, 10 mm adjust code, G1/8 port, and PT thread. Mounting is Basic, FA, or LB only; there is no back cover or SDB option. Since this SKU lacks the -S magnet, it cannot take a sensor; if you need sensing on the MBLJ, specify -S for CMSG/DMSG/EMSG switches instead of the older CS1-M/DS1-M.
At 250 mm stroke, the 12 mm rod is susceptible to bending under side loads; use a guide to prevent rod damage. The adjuster is a stop, not a lock.
Upgrade checklist
- ✓ Order the MBLJ32X250-10 (same bore/stroke/adjust)
- ✓ Same 240–250 mm adjustable window
- ✓ Adjuster is a stop, not a lock
- ✓ No back cover / SDB — plan an FA/LB mount
- ✓ Sensor: swap CS1-M/DS1-M → CMSG/DMSG/EMSG
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.1 – 1.0 MPa operating pressure.
- check The rear adjuster sets the end position — it is not a load lock.
- check No back-cover / SDB on adjustable-stroke — use FA / LB.
- check Front/rear covers are threaded — not for field disassembly.
- check For new builds, specify the MBLJ32X250-10 instead of this discontinued model.
Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-10 FAQ
Yes, the MALJ32X250-10 is discontinued. The direct replacement is the MBLJ32X250-10, which matches the 32 mm bore, 250 mm stroke, 10 mm adjust code, and G1/8 port. The MBLJ upgrades the threaded covers to a riveted rolling-packed body.
The 10 mm rear adjuster creates a usable stroke window of 240-250 mm. The adjuster is a travel stop, not a lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
Direct Upgrade
The MBLJ32X250-10 replaces this model 1:1.
Fast Dispatch
MBLJ replacements are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Recommended AirTAC MBLJ Replacements
Request a Quote (Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-10 → MBLJ32X250-10)
Tell us the quantity and destination — we quote the direct MBLJ32X250-10 replacement with price, stock and lead time, usually within 7-8 hours.