This model is discontinued
AirTAC has phased out the MALJ series. You can still order this code here: we ship the direct replacement MBLJ32X250-75, with the same bore, stroke, output force, port and mounting, so it fits the same application. The MBLJ replacement upgrades to a riveted rolling-packed body and CMSG / DMSG / EMSG sensors (the MAL used CS1-M / DS1-M).
Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-75
The AirTAC Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-75 is a double-acting aluminum mini cylinder with a rear adjustable-stroke stopper: you can trim up to 75 mm, giving a usable end-position window from 175 to 250 mm. This model is discontinued — the direct replacement is the MBLJ32X250-75.
- BoreØ32 mm
- Stroke250 mm
- Adjust window175–250 mm
- Port sizeG1/8
- Rod threadM10×1.25
- StatusDiscontinued → MBLJ32X250-75
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-75
The AirTAC MALJ32X250-75 is a discontinued double-acting, double-rod mini cylinder with a 32mm bore and 250mm stroke. A 75mm rear adjuster creates a usable end-position window of 175-250mm. The direct replacement is the MBLJ32X250-75, which matches the bore, stroke, adjuster, G1/8 port, and FA/LB mounting.
This SKU lacks a magnet (-S), so it cannot accept a position sensor. The adjuster sets travel but does not hold load without live air. Upgrading to the MBLJ brings a riveted rolling-packed body and modern CMSG/DMSG/EMSG sensors, replacing the MALJ threaded covers and CS1-M/DS1-M switches. End impact relies on a fixed rubber bumper, not an adjustable cushion.
Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-75 Technical Specifications
| Model | Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-75 |
|---|---|
| Series | MALJ adjustable-stroke mini cylinder (discontinued) |
| Replacement | MBLJ32X250-75 |
| Bore size | Ø32 mm |
| Stroke | 250 mm |
| Adjustable window | 175 – 250 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
The rear adjuster is a travel stop, not a lock — it sets the end position but does not hold the load without live air. No back-cover code and no SDB on adjustable-stroke. The MBLJ32X250-75 carries the same ratings.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
MALJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod MAL push of the same bore. The MBLJ32X250-75 matches these values.
Model Code: Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-75
| MALJ | Adjustable-stroke aluminum mini cylinder, double acting (discontinued). |
|---|---|
| 32 | Bore size in mm (20/25/32/40). |
| ×250 | Nominal stroke length in mm. |
| -75 | Adjustable amount: trim the end to a 175–250 mm window. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBLJ uses CMSG/DMSG/EMSG). |
Replacement: MALJ → MBLJ. No back-cover (CA/U/CM) and no SDB. Mounting: FA / LB.
Where the Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-75 Is Used
PCB Router Depth
Trim the rear travel up to 75mm to fine-tune the cutting depth on a PCB depaneling router, preventing the 12mm rod from crashing into the fixture support plate.
Textile Guide Tension
Adjust the end position to maintain exact fabric tension on a weaving loom, letting the fixed rubber bumper absorb the repetitive 250mm stroke impacts without air cushions.
Replacing the Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-75 with MBLJ32X250-75
To replace the MALJ32X250-75, order the exact direct replacement MBLJ32X250-75. Confirm the 32mm bore, 250mm stroke, 75mm adjust code, G1/8 port, PT thread, and FA/LB mounting. Since this SKU lacks a magnet, you lose position sensing; adding an -S on the MBLJ enables CMSG/DMSG/EMSG switches. The rear adjuster is a travel stop, not a lock. At 250mm, watch rod-bending side loads.
Upgrade checklist
- ✓ Order the MBLJ32X250-75 (same bore/stroke/adjust)
- ✓ Same 175–250 mm adjustable window
- ✓ Adjuster is a stop, not a lock
- ✓ No back cover / SDB — plan an FA/LB mount
- ✓ Sensor: swap CS1-M/DS1-M → CMSG/DMSG/EMSG
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.1 – 1.0 MPa operating pressure.
- check The rear adjuster sets the end position — it is not a load lock.
- check No back-cover / SDB on adjustable-stroke — use FA / LB.
- check Front/rear covers are threaded — not for field disassembly.
- check For new builds, specify the MBLJ32X250-75 instead of this discontinued model.
Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-75 FAQ
Yes, the MALJ32X250-75 is discontinued. The direct replacement is the MBLJ32X250-75, matching the 32mm bore, 250mm stroke, 75mm adjuster, G1/8 port, and FA/LB mounting. The MBLJ upgrades the threaded covers to a riveted rolling-packed body.
The 75mm rear adjuster lets you trim the end position, creating a usable stroke window from 175mm to 250mm. It acts as a travel stop and does not hold the load without live air.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
Direct Upgrade
The MBLJ32X250-75 replaces this model 1:1.
Fast Dispatch
MBLJ replacements are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Recommended AirTAC MBLJ Replacements
Request a Quote (Airtac MALJ32 Adjustable Mini Cylinder MALJ32X250-75 → MBLJ32X250-75)
Tell us the quantity and destination — we quote the direct MBLJ32X250-75 replacement with price, stock and lead time, usually within 7-8 hours.