This model is discontinued
AirTAC has phased out the MALJ series. You can still order this code here: we ship the direct replacement MBLJ32X60-10S, with the same bore, stroke, output force, port and mounting, so it fits the same application. The MBLJ replacement upgrades to a riveted rolling-packed body and CMSG / DMSG / EMSG sensors (the MAL used CS1-M / DS1-M).
Airtac MALJ32 Adjustable Mini Cylinder MALJ32X60-10S
The AirTAC Airtac MALJ32 Adjustable Mini Cylinder MALJ32X60-10S is a double-acting aluminum mini cylinder with a rear adjustable-stroke stopper: you can trim up to 10 mm, giving a usable end-position window from 50 to 60 mm. This model is discontinued — the direct replacement is the MBLJ32X60-10S.
- BoreØ32 mm
- Stroke60 mm
- Adjust window50–60 mm
- Port sizeG1/8
- Rod threadM10×1.25
- StatusDiscontinued → MBLJ32X60-10S
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MALJ32 Adjustable Mini Cylinder MALJ32X60-10S
The AirTAC MALJ32X60-10S is a discontinued double-acting double-rod cylinder with a 10 mm rear travel stopper. The direct replacement is the MBLJ32X60-10S, matching the 60 mm stroke, 10 mm adjust code, G1/8 port, and M10x1.25 rod thread.
The rear adjuster is a travel stop, not a lock; it sets the end position but cannot hold a load without live air. End impact relies on a fixed rubber bumper, as there is no adjustable air cushion. Upgrading to the MBLJ shifts you from threaded covers to a riveted rolling-packed body, and the -S magnet changes from the older CS1-M / DS1-M switches to the CMSG / DMSG / EMSG sensor family.
Airtac MALJ32 Adjustable Mini Cylinder MALJ32X60-10S Technical Specifications
| Model | Airtac MALJ32 Adjustable Mini Cylinder MALJ32X60-10S |
|---|---|
| Series | MALJ adjustable-stroke mini cylinder (discontinued) |
| Replacement | MBLJ32X60-10S |
| Bore size | Ø32 mm |
| Stroke | 60 mm |
| Adjustable window | 50 – 60 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
The rear adjuster is a travel stop, not a lock — it sets the end position but does not hold the load without live air. No back-cover code and no SDB on adjustable-stroke. The MBLJ32X60-10S carries the same ratings.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
MALJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod MAL push of the same bore. The MBLJ32X60-10S matches these values.
Model Code: Airtac MALJ32 Adjustable Mini Cylinder MALJ32X60-10S
| MALJ | Adjustable-stroke aluminum mini cylinder, double acting (discontinued). |
|---|---|
| 32 | Bore size in mm (20/25/32/40). |
| ×60 | Nominal stroke length in mm. |
| -10 | Adjustable amount: trim the end to a 50–60 mm window. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBLJ uses CMSG/DMSG/EMSG). |
Replacement: MALJ → MBLJ. No back-cover (CA/U/CM) and no SDB. Mounting: FA / LB.
Where the Airtac MALJ32 Adjustable Mini Cylinder MALJ32X60-10S Is Used
Aluminum Extrusion End-Face
Fine-tune the cutting position on an aluminum extrusion saw. The 10 mm rear stopper lets operators trim the 60 mm stroke to hit a precise 55 mm cut length without adding external spacers.
Carton Flap Folder
Adjust the reach on a packaging line folder to accommodate varying carton heights. The fixed rubber bumper absorbs the repeated impact of the folding arm at the end of every cycle.
Replacing the Airtac MALJ32 Adjustable Mini Cylinder MALJ32X60-10S with MBLJ32X60-10S
To replace this MALJ32X60-10S with the MBLJ32X60-10S, confirm the 32 mm bore, 60 mm stroke, 10 mm adjust code, G1/8 port, PT thread, and FA or LB mounting. There is no back-cover or SDB option. The -S magnet requires CMSG / DMSG / EMSG sensors on the new body. Remember the adjuster sets end position but does not hold load without air.
At 60 mm stroke, rod bending is negligible.
Upgrade checklist
- ✓ Order the MBLJ32X60-10S (same bore/stroke/adjust)
- ✓ Same 50–60 mm adjustable window
- ✓ Adjuster is a stop, not a lock
- ✓ No back cover / SDB — plan an FA/LB mount
- ✓ Sensor: swap CS1-M/DS1-M → CMSG/DMSG/EMSG
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.1 – 1.0 MPa operating pressure.
- check The rear adjuster sets the end position — it is not a load lock.
- check No back-cover / SDB on adjustable-stroke — use FA / LB.
- check Front/rear covers are threaded — not for field disassembly.
- check For new builds, specify the MBLJ32X60-10S instead of this discontinued model.
Airtac MALJ32 Adjustable Mini Cylinder MALJ32X60-10S FAQ
Yes, the MALJ32X60-10S is discontinued. The direct replacement is the MBLJ32X60-10S, which matches the 32 mm bore, 60 mm stroke, 10 mm adjust code, and G1/8 port. You will need to switch from the older CS1-M / DS1-M switches to the CMSG / DMSG / EMSG sensor family for the new riveted body.
The 10 mm adjuster creates a usable stroke window of 50-60 mm. The adjuster is a travel stop, not a lock, and it will not hold a load without live air.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
Direct Upgrade
The MBLJ32X60-10S replaces this model 1:1.
Fast Dispatch
MBLJ replacements are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Recommended AirTAC MBLJ Replacements
Request a Quote (Airtac MALJ32 Adjustable Mini Cylinder MALJ32X60-10S → MBLJ32X60-10S)
Tell us the quantity and destination — we quote the direct MBLJ32X60-10S replacement with price, stock and lead time, usually within 7-8 hours.