Airtac MPGH Hinge Mount Type Cylinder MPGH6X25N
Genuine AirTAC hinge mount cylinder, order code MPGH6X25N from the MPGH6 range. The options this code selects are decoded below; series data follow the official AirTAC catalog.
- Stroke25 mm
- MagnetNo magnet
- Rod end and mountingPlain rod (N)
- ActionDouble acting
- Bore / rodØ6 / Ø3 mm
- Standard strokes5 mm steps to 25 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MPGH Hinge Mount Type Cylinder MPGH6X25N
MPGH6X25N is the plain-rod member of the AirTAC MPG hinge mount cylinder series: the N option code removes the male thread from the Dia 3 mm rod, leaving a smooth end for direct attachment to a customer-made tip, pin or bracket. It is double acting with a Dia 6 mm bore, 25 mm of stroke, and pivots on a rear clevis so the cylinder can follow a swinging load.
Because there is no magnet, the sensor grooves around the body cannot be used for end-position detection on this code; the magnet belongs to the S sibling. The rod guide remains precise without extra lubrication, bumpers cushion both ends, and the piston runs across the 30-500 mm/s speed band at a supply of 0.15-0.7 MPa (22-100 psi). Note that the catalog rod-end accessories, such as I and Y joints and bumper caps, are listed for the threaded rod, so confirm fitment from the datasheet before combining them with a plain rod.
Airtac MPGH Hinge Mount Type Cylinder MPGH6X25N Technical Specifications
| Order code | MPGH6X25N |
|---|---|
| Product | Hinge Mount Cylinder |
| Stroke | 25 mm |
| Magnet | No magnet |
| Rod end and mounting | Plain rod (N) |
| Action | Double acting |
|---|---|
| Bore / rod | Ø6 / Ø3 mm |
| Standard strokes | 5 mm steps to 25 mm |
| Force at 0.5 MPa | Push 14.2 N · pull 10.6 N |
| Port | M3×0.5 |
| Mounting | Rear clevis (hinge) |
| Fluid | Air (filtered by 40 µm element) |
| Operating pressure | 0.15-0.7 MPa (22-100 psi) |
| Proof pressure | 1.2 MPa (175 psi) |
| Temperature | -20 to +70 °C |
| Piston speed | 30-500 mm/s |
| Cushion | Bumper |
Source: AirTAC Products Catalog 2026A (PDF01-P0508..P0509), MPG series theoretical force, specifications, strokes and ordering code.
How to choose
Choose MPGH6X25N over MPGH6X25 when the load attaches directly to the rod and a male thread would be in the way; choose MPGH6X25 when you need the catalog I or Y joints and bumper caps that fit the threaded end. If position feedback matters, step up to MPGH6X25S, the only Dia 6 code with the magnet. If 25 mm is more travel than the mechanism needs, MPGH6X5 through MPGH6X20 shorten the stroke in 5 mm steps.
Applications
Direct-push light clamping
A plain rod end lets a custom pad press straight onto light parts; at 0.5 MPa the cylinder delivers 14.2 N push, sized for small holding tasks rather than heavy clamps.
Custom-tip mini actuators
Machine builders who turn their own tips fit them directly to the unthreaded Dia 3 mm rod, keeping the rear clevis pivot on a 25 mm stroke inside tight envelopes.
Low-speed test rigs
The 30-500 mm/s speed range and bumper cushion at both ends make the plain-rod body useful for gentle, repeatable motion on small laboratory or assembly devices.
FAQ
Which specifications define MPGH6X25N?
Dia 6 mm bore, Dia 3 mm plain (unthreaded) rod, 25 mm stroke from the 5 to 25 mm range with +1.0/0 mm tolerance, double acting, 14.2 N push and 10.6 N pull at 0.5 MPa, M3x0.5 port, 0.15-0.7 MPa (22-100 psi) operating pressure, 1.2 MPa proof pressure, -20 to +70 C, 30-500 mm/s piston speed, bumper cushion, 40 um filtered air.
Does the N rod end change sensing or accessories?
The N option only removes the male thread from the rod; the cylinder still mounts by the rear clevis, and the SDB rear clevis bracket is available as an accessory. It does not add a magnet: with no magnet in this code, the sensor grooves cannot deliver position detection, which requires MPGH6X25S instead.