Airtac MPGH Hinge Mount Type Cylinder MPGH6X25SN
Genuine AirTAC hinge mount cylinder, order code MPGH6X25SN from the MPGH6 range. The options this code selects are decoded below; series data follow the official AirTAC catalog.
- Stroke25 mm
- MagnetMagnet
- Rod end and mountingPlain rod (N)
- ActionDouble acting
- Bore / rodØ6 / Ø3 mm
- Standard strokes5 mm steps to 25 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MPGH Hinge Mount Type Cylinder MPGH6X25SN
The MPGH6X25SN is the longest-stroke build of the AirTAC MPG hinge series: a double-acting cylinder with a 6 mm bore and the full 25 mm stroke offered on this size, pivoting from a rear clevis so the rod can follow the load through its arc. Bumpers cushion both ends of travel, air is fed through M3x0.5 ports at 0.15-0.7 MPa (22-100 psi), and the piston runs from 30 to 500 mm/s.
The S in the code adds a magnet, so a switch reads position along the sensor grooves that run around the body with no extra brackets to fit. The trailing N means the rod ships plain, without a male thread, so screw-on I and Y joints and bumper caps cannot be used; if you want those threaded rod-end accessories, order MPGH6X25 instead. The SDB rear clevis bracket is available for the pivot mount.
Airtac MPGH Hinge Mount Type Cylinder MPGH6X25SN Technical Specifications
| Order code | MPGH6X25SN |
|---|---|
| Product | Hinge Mount Cylinder |
| Stroke | 25 mm |
| Magnet | Magnet |
| Rod end and mounting | Plain rod (N) |
| Action | Double acting |
|---|---|
| Bore / rod | Ø6 / Ø3 mm |
| Standard strokes | 5 mm steps to 25 mm |
| Force at 0.5 MPa | Push 14.2 N · pull 10.6 N |
| Port | M3×0.5 |
| Mounting | Rear clevis (hinge) |
| Fluid | Air (filtered by 40 µm element) |
| Operating pressure | 0.15-0.7 MPa (22-100 psi) |
| Proof pressure | 1.2 MPa (175 psi) |
| Temperature | -20 to +70 °C |
| Piston speed | 30-500 mm/s |
| Cushion | Bumper |
Source: AirTAC Products Catalog 2026A (PDF01-P0508..P0509), MPG series theoretical force, specifications, strokes and ordering code.
How to choose
Choose MPGH6X25SN when you need the maximum 25 mm stroke on a 6 mm bore, magnet-based position sensing, and a rod that attaches by clamp or clevis rather than thread. Compared with MPGH6X25 you gain the magnet but lose the male thread; compared with MPGH6X25S you keep the magnet and drop the threaded rod; and against MPGH6X20SN you get 5 mm more travel, in 5 mm steps the catalog sizes up to 25 mm on this bore.
Applications
Position feedback on compact slides
The built-in magnet works with switches on the body grooves to confirm open/closed positions of small gates or sliders, with stroke tolerance of +1.0/0 mm.
Conveyor gate push-off
The rear clevis pivot swings the 25 mm stroke as a diverter or kicker on light-duty conveyor lines, cushioned by bumpers at both ends.
Fine adjustment linkages
A plain rod clamped in an adjustment screw or linkage lets the hinge pivot compensate for misalignment during 30-500 mm/s positioning moves.
FAQ
What are the key figures of the MPGH6X25SN?
Double acting, 6 mm bore, 3 mm rod, 25 mm stroke, push 14.2 N and pull 10.6 N at 0.5 MPa, M3x0.5 ports, operating pressure 0.15-0.7 MPa (22-100 psi), proof pressure 1.2 MPa, temperature -20 to +70 C, piston speed 30-500 mm/s, bumper cushion, magnet fitted, plain rod (N).
What can I attach to the plain N rod of this cylinder?
The N rod end has no male thread, so screw-on I and Y joints and bumper caps from the MPG accessory range will not fit it; use a clamp, clevis or bracket on the plain rod. If you need threaded accessories, order MPGH6X25, which has the male-thread rod end.