Airtac PB Pen-type Cylinder PB12X15SR
The AirTAC PB Pen-type Cylinder PB12X15SR is a double-acting pen-size (mini) air cylinder with a Ø12mm bore and 15mm stroke. Its slim round barrel and back cover are stainless steel, the M5×0.8 ports keep plumbing compact, and the fast, low-friction piston suits high-cycle small-part handling.
- BoreØ12 mm
- Stroke15 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM10×1.0
- CushionElastic bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PB Pen-type Cylinder PB12X15SR
The AirTAC PB12X15SR is a double-acting JIS pen-size mini cylinder engineered for high-frequency small-part motion within tight jigs. It features a slim SUS304 stainless steel barrel and piston rod, offering excellent durability in damp or mildly corrosive environments while keeping end-of-arm payload low. Delivering 56.5 N of push force at 0.5 MPa, this 12 mm bore unit is both compact and fast.
This specific configuration includes a built-in piston magnet (S) for position detection using AirTAC reed or electronic switches, and an R axial air inlet for in-line plumbing. The M5x0.8 port matches the 12 mm bore standard. Deceleration is handled by a fixed TPU bumper at each end, which absorbs impact over the final few millimeters of travel rather than acting as a lock. For rapid cycling with heavy tooling, metering out the exhaust or adding an external shock absorber is recommended.
Airtac PB Pen-type Cylinder PB12X15SR Technical Specifications
| Model | Airtac PB Pen-type Cylinder PB12X15SR |
|---|---|
| Series | PB JIS pen-size mini cylinder |
| Bore size | Ø12 mm |
| Rod diameter | Ø5 mm |
| Stroke | 15 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC PB pen-size datasheet. Piston rod and barrel are stainless steel. Confirm bore, stroke and back-cover option against the product label before installation.
Theoretical Output Force (Ø12mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 56.5 N | 46.7 N |
| 0.7 MPa (max) | 79.1 N | 65.4 N |
Values are taken from the AirTAC PB thrust table. Because pull acts on the rod-side annular area, pull force is always lower than push. Actual usable force is reduced by friction — size with a margin.
Model Code: Airtac PB Pen-type Cylinder PB12X15SR
| PB | JIS pen-size double-acting mini-cylinder series. |
|---|---|
| 12 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| CB / U / R | Back cover: CB double clevis, U 90° side inlet, R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PSB (single-acting push), PTB (single-acting pull), PBD (double rod), PBJ (adjustable stroke), PBR (front-mount).
Where the Airtac PB Pen-type Cylinder PB12X15SR Is Used
PCB Depaneling Jig
Drives a small cutting blade or separator pin in a tight electronics assembly fixture, utilizing the 15 mm stroke to cleanly singulate printed circuit boards.
Blister Pack Sealing
Applies a precise 34 N safe clamping force on thin film covers within a compact packaging station, benefiting from the SUS304 build against humid environments.
Lab Dispense Valve
Actuates a micro-dispense nozzle for reagent routing, where the R axial inlet saves space and the S magnet confirms valve open/close positions to the controller.
Is the Airtac PB Pen-type Cylinder PB12X15SR the Right Cylinder?
When sizing this actuator, the PB12X15SR provides a theoretical push of 56.5 N at 0.5 MPa. If you need to step down, the adjacent 10 mm bore offers 39.3 N push; stepping up to the 16 mm bore yields 100.5 N push at the same pressure. Keep in mind a plain PB body does not hold position if air pressure is lost or the valve is centered, as the piston will drift, so an external rod lock is required for fail-safe holding.
Confirm your ordering essentials: 12 mm bore, 15 mm stroke, M5x0.8 port, S magnet for sensing, and R axial inlet. The Ø5 mm piston rod utilizes an M10x1.0 rod-end thread for load coupling. Because the rod is designed strictly for coaxial thrust, avoid side loading and utilize an external linear bearing if guiding off-axis loads.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Slim pen body vs. a standard round cylinder
- ✓ Back cover: CB / U / R inlet direction
- ✓ Magnet (S) for sensors?
- ✓ Mounting: LB / FA / CJ or front thread
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
- check Fit dust caps to ports during long-term storage.
- check Installation by qualified personnel per AirTAC docs.
Airtac PB Pen-type Cylinder PB12X15SR FAQ
The 12 mm bore double-acting single rod provides 56.5 N push and 46.7 N pull at 0.5 MPa. At the maximum operating pressure of 0.7 MPa, it yields 79.1 N push and 65.4 N pull. Operating pressure ranges from 0.15-0.7 MPa, with a speed of 50-800 mm/s.
No, the piston will drift if air is lost or the valve is centered. The fixed TPU bumper only decelerates the rod near stroke end and does not function as a brake. For vertical loads, you should plan for an external stop or rod lock, and add a linear bearing to protect the Ø5 mm rod from side loads.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PB Pen-Size Cylinders
Request a Quote for Airtac PB Pen-type Cylinder PB12X15SR
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.