Airtac PC Threaded Straight Connector PC1001-S
SUS304 stainless variant (-S)The AirTAC Airtac PC Threaded Straight Connector PC1001-S is a genuine male connector for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale connector
- SeriesPC
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PC Threaded Straight Connector PC1001-S
The PC1001-S is AirTAC's PC series one-touch male connector in the SUS304 stainless-steel variant. It joins Dia 10 mm soft nylon or polyurethane tubing to a 1/8in PT male thread. On the PC and POC straight connectors the -S suffix changes the fitting body itself to Stainless steel 304, and AirTAC states all parts are copper-free - the release button and chuck remain POM, with an aluminium-alloy guide, stainless spring gasket and NBR O-ring.
Connection is genuinely one-touch: push the tube fully home and the stainless spring gasket and chuck grip it for a pressure-tight seal; press the release ring and the tube slides straight back out. Ratings are identical to the standard PC1001 - 0 to 1.0 MPa working pressure, 1.5 MPa proof pressure, -750 mmHg vacuum, and -20 to +70 C. Stainless buys you corrosion resistance and copper-free construction, not a higher rating.
Airtac PC Threaded Straight Connector PC1001-S Technical Specifications
| Model | Airtac PC Threaded Straight Connector PC1001-S |
|---|---|
| Type | Male connector |
| Series | PC |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PC Threaded Straight Connector PC1001-S
| PC | Male connector. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PC Threaded Straight Connector PC1001-S Is Used
Electronics fab process lines
Copper-free SUS304 construction suits semiconductor and PCB plant air drops, where dissolved copper can contaminate rinse and process baths downstream of the fitting.
Marine and salt-air compressor manifolds
A 10mm stainless body with a 1/8in thread resists salt-spray corrosion on boat and offshore platform pneumatic runs where a plated brass PC1001 would pit and seize.
Plating and wash-down hoist cylinders
Dia 10 tube straight into the cylinder port on electroplating hoists and rinse-tank actuators, where chemical splash would rapidly attack a standard PBT-and-brass connector.
Is the Airtac PC Threaded Straight Connector PC1001-S the Right Part?
You are on the middle-upper rung of the 1/8in ladder: step down to the PC801-S for Dia 8 tube feeding smaller actuators and sensors, or up to the PC1201-S for Dia 12 tube on higher-flow main runs. Bore is what changes - flow capacity follows the tube, not the fitting shape. Before ordering, match the 1/8in PT thread to the port and remember the tube OD must match exactly: this fitting will not hold 3/8in or 13 mm tube regardless of how hard you push it.
Where a straight connector is the wrong answer: use a PL901-S elbow when the tube must turn 90 degrees at the port, or a PM1001 bulkhead when you need to pass through a panel wall with a locknut. Both share this Dia 10 / 1/8in interface on the PC ladder.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PC Threaded Straight Connector PC1001-S FAQ
Working pressure 0 to 1.0 MPa (0 to 10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, temperature -20 to +70 C. It joins Dia 10 mm soft nylon or polyurethane tube to a 1/8in PT male thread. The fitting body is Stainless steel 304 and copper-free; the release button and chuck are POM, the guide aluminium alloy, the spring gasket stainless, the O-ring NBR.
Yes. AirTAC's dimension tables for the stainless variant match the standard part, so it swaps in without re-drawing the machine. What changes is the body material: SUS304, copper-free, for corrosion resistance and copper-sensitive processes. The pressure and temperature ratings are unchanged, and the same soft nylon or polyurethane tubing applies - hard-rigid tube will not seat correctly on the chuck.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PC Threaded Straight Connector PC1001-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.