Airtac PEB T-Shaped Straight Thread Tee Connector PEB1004
The AirTAC Airtac PEB T-Shaped Straight Thread Tee Connector PEB1004 is a genuine male branch tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale branch tee
- SeriesPEB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEB T-Shaped Straight Thread Tee Connector PEB1004
The PEB1004 is an AirTAC PEB male branch tee, a one-touch fitting that turns a single Dia 10 mm tube line into two while presenting a male 1/2 in PT thread on the branch. The run of the tee is push-in tube on both legs; the branch outlet screws straight into a tapped port. To connect, push the soft nylon or polyurethane tube fully home until it bottoms out - the stainless spring gasket and POM chuck grip the tube wall instantly. Pressing the release ring square to the body frees the tube again.
This is the resin and brass one-touch profile, not the high-temperature metal line: working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum to -750 mmHg (10 Torr), proof pressure 1.5 MPa, and a service temperature of -20 to +70 C. The body and tee legs are moulded PBT, the release button and chuck are POM, and the 1/2 in male stud arrives with sealant already applied to the thread, so it can be wound straight into a PT port with no extra tape or paste.
Airtac PEB T-Shaped Straight Thread Tee Connector PEB1004 Technical Specifications
| Model | Airtac PEB T-Shaped Straight Thread Tee Connector PEB1004 |
|---|---|
| Type | Male branch tee |
| Series | PEB |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEB T-Shaped Straight Thread Tee Connector PEB1004
| PEB | Male branch tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEB T-Shaped Straight Thread Tee Connector PEB1004 Is Used
Dropping a Dia 10 branch off a machine air spine
On a palletiser or case-packer with a Dia 12 main feed line, the PEB1004 lets you tee a Dia 10 take-off to a valve island without cutting the spine or adding threaded fittings between tubes.
Branching to a cylinder on a press or saw frame
Where a pneumatic clamping cylinder on a CNC saw or hot press needs a signal or pilot line added, the 1/2 in PT branch stud screws into the spare tapped port and the Dia 10 legs stay in the run.
Adding a blow-off or coolant-air tap in a woodworking shop
Screw the 1/2 in stud into a manifold port beside a wide-belt sander and push Dia 10 hose home to feed a dust-clearing air knife, with the one-touch release letting you re-route the drop as jigs change.
Is the Airtac PEB T-Shaped Straight Thread Tee Connector PEB1004 the Right Part?
At the 1/2 in thread position, the PEB ladder covers Dia 8, Dia 10 and Dia 12 only - AirTAC does not make a PEB in Dia 4 or Dia 6 with a 1/2 in stud, so small-bore branches need a 1/8 in or 1/4 in thread instead. One size down is PEB804 (Dia 8, 1/2 in), which suits lighter-framed cylinders and gives a modest drop in air demand per branch; one size up is PEB1204 (Dia 12, 1/2 in), the top of the resin range, for feed lines running several actuators. The 3/8 in option (PEB1003) keeps the same Dia 10 bore if your port is smaller.
Tube OD must match exactly: the chuck on this part seats on a 10 mm outside wall and will not seal on 3/8 in or 12 mm tube. If your port is female rather than tapped, a PLF female elbow or a PMF bulkhead connector is the shape to look at instead; if the branch needs to swivel to clear structure, the PH universal male elbow does that job rather than a fixed tee.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEB T-Shaped Straight Thread Tee Connector PEB1004 FAQ
The PEB1004 is a PEB male branch tee for Dia 10 mm tube with a 1/2 in PT male thread. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), it handles vacuum down to -750 mmHg (10 Torr), proof pressure is 1.5 MPa, and the temperature range is -20 to +70 C. Tubing must be soft nylon or polyurethane. The resin body is grey as standard, the POM release button and chuck grip the tube one-touch, and the male thread ships with sealant pre-applied.
No. The chuck is machined for 10 mm outside diameter only, and a Dia 6 tube will neither seal nor lock in it. AirTAC also does not list a Dia 6 PEB at 1/2 in thread at all - the 1/2 in ladder stops at Dia 8, 10 and 12. For Dia 6 tube on a 1/2 in port, put a reducing adapter in the port and use a PEB601 (1/8 in) or PEB602 (1/4 in) branch tee instead.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEB T-Shaped Straight Thread Tee Connector PEB1004
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.