Airtac PEB T-Shaped Straight Thread Tee Connector PEB801
The AirTAC PEB T-Shaped Straight Thread Tee Connector PEB801 is a genuine male branch tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale branch tee
- SeriesPEB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEB T-Shaped Straight Thread Tee Connector PEB801
The PEB801 is an AirTAC PEB male branch tee, a one-touch fitting that splits a Dia 8 mm tube run into a 90 degree branch ending in a male 1/8in PT stud. Unlike the PED run tee, where the threaded stud sits in line with the run, the PEB stud projects sideways from the branch leg, so the main flow passes straight through the body while the branch taps off at a right angle.
To make the joint, push the tube firmly into the collet until it bottoms out; the stainless spring gasket and chuck jaws grip the tube wall, and pressing the POM release ring frees it again. This resin-line part is rated 0-1.0 MPa (0-10 kgf/cm2) working pressure, 1.5 MPa proof pressure, -750 mmHg vacuum and -20 to +70 C. The 1/8in thread arrives with sealant already applied, and the PBT body carries a brass stud for the ported side.
Airtac PEB T-Shaped Straight Thread Tee Connector PEB801 Technical Specifications
| Model | Airtac PEB T-Shaped Straight Thread Tee Connector PEB801 |
|---|---|
| Type | Male branch tee |
| Series | PEB |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEB T-Shaped Straight Thread Tee Connector PEB801
| PEB | Male branch tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEB T-Shaped Straight Thread Tee Connector PEB801 Is Used
Valve manifold feed on a packaging machine
Branch a Dia 8 supply drop sideways off the main run into the 1/8in port of a solenoid valve manifold, while the run continues straight through to the next drop without extra couplers.
Blow-off tap on a bottling conveyor
Take a right-angle branch off a Dia 8 line running the length of the conveyor to feed a small air nozzle that clears dust or spilled product, keeping the main circuit untouched.
Gripper supply inside a CNC assembly cell
Feed a pneumatic gripper on a pick-and-place head from a branch leg angled away from the moving axis, using the male 1/8in stud screwed directly into the gripper's PT port.
Is the Airtac PEB T-Shaped Straight Thread Tee Connector PEB801 the Right Part?
On the PEB ladder at 1/8in thread, the neighbouring sizes are PEB601 (Dia 6) below and PEB1001 (Dia 10) above. Stepping down to Dia 6 saves space and suits lighter-bore circuits but reduces the air volume the run can carry; stepping up to Dia 10 lowers restriction on longer runs and higher-demand branches. The same Dia 8 tube is also offered on 1/4in thread as PEB802 if the port calls for a larger stud. Whatever you choose, the chuck is collet-sized to one tube OD only - this fitting holds Dia 8 mm soft nylon or polyurethane and will not seal on 5/16in (8 mm nominal Imperial) tube or on any other OD.
Pick a branch tee over a plain union tee when you need to tap a sideways feed off a straight run without re-routing the main line; pick the PED version instead if the stud must be inline with the run, or a PMF bulkhead connector if you need to pass through a panel.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEB T-Shaped Straight Thread Tee Connector PEB801 FAQ
It is a male branch tee for Dia 8 mm tubing with a male 1/8in PT thread. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), proof pressure 1.5 MPa, vacuum rating -750 mmHg (10 Torr), and operating temperature -20 to +70 C. It accepts soft nylon or polyurethane tube only.
Both join three legs, but the position of the male stud differs. On the PEB the threaded stud sits on the 90 degree branch leg, so the straight run passes through the body undisturbed - the stud is effectively a side outlet. On the PED the stud is inline with one run leg. Choose PEB when the port you are feeding faces sideways from the main line and PED when the port is at the end of the run direction.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEB T-Shaped Straight Thread Tee Connector PEB801
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.