Airtac PEB T-Shaped Straight Thread Tee Connector PEB802
The AirTAC Airtac PEB T-Shaped Straight Thread Tee Connector PEB802 is a genuine male branch tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale branch tee
- SeriesPEB
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEB T-Shaped Straight Thread Tee Connector PEB802
The PEB802 is an AirTAC PEB male branch tee, the resin one-touch fitting that takes a Dia 8 mm tube branch off a 1/4 inch PT male thread. The thread sits on the run of the tee, so it mounts straight into a manifold port or valve outlet while the two push-in legs continue the main line and drop the branch at 90 degrees.
To connect, push the Dia 8 tube into a leg until it bottoms - the internal chuck grips it against a stainless spring gasket and NBR O-ring seal. Press the POM release ring toward the body and the tube pulls free. This P-prefix part runs on the resin spec: 0 to 1.0 MPa working pressure, -750 mmHg vacuum, 1.5 MPa proof pressure, -20 to +70 C. The body is PBT, the stud is brass, and the 1/4 thread arrives pre-coated with sealant.
Airtac PEB T-Shaped Straight Thread Tee Connector PEB802 Technical Specifications
| Model | Airtac PEB T-Shaped Straight Thread Tee Connector PEB802 |
|---|---|
| Type | Male branch tee |
| Series | PEB |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEB T-Shaped Straight Thread Tee Connector PEB802
| PEB | Male branch tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEB T-Shaped Straight Thread Tee Connector PEB802 Is Used
Branching a solenoid valve outlet
Threaded into the 1/4 PT outlet of a solenoid valve, the PEB802 splits one supply into a continuing run and a 90 degree branch feeding an air gun or second actuator.
Manifold drop to a rotary actuator
On a pneumatic manifold serving a packaging line, the branch leg drops Dia 8 tube down to a rotary actuator port while the main line keeps feeding downstream stations.
Jetting line off a conveyor air supply
A Dia 8 branch tee at the conveyor frame's air feed lets a cleaning or blow-off jet tap the supply without breaking the main tube run along the machine.
Is the Airtac PEB T-Shaped Straight Thread Tee Connector PEB802 the Right Part?
On the 1/4 inch rung of the PEB ladder, Dia 8 sits between PEB602 (Dia 6) and PEB1002 (Dia 10). Stepping down to Dia 6 trims cost and suits lighter actuator feeds; stepping up to Dia 10 lowers the pressure drop on longer branch runs. Both neighbour sizes share the same 1/4 thread, so you can resize the branch without repicking the port.
The branch shape matters: it angles 90 degrees off the tee's centreline, while a PED male run tee points its branch along the run and a PYB Y splits at 45. Match the tube OD exactly - a Dia 8 chuck will not grip 5/16 or 1/4 inch tube. If you need stainless instead of a brass stud, the PEB802S swaps the stud to SUS304 while keeping the identical body and ratings.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEB T-Shaped Straight Thread Tee Connector PEB802 FAQ
The PEB802 is a male branch tee for Dia 8 mm tube on a 1/4 inch PT male thread. Working pressure is 0 to 1.0 MPa (0 to 10 kgf/cm2), vacuum to -750 mmHg (10 Torr), proof pressure 1.5 MPa, and the temperature range is -20 to +70 C. It is the resin spec profile with a PBT body, brass stud and NBR O-ring.
Both mount a 90 degree leg on a male thread, but the geometry differs. On the PEB802 the threaded stud sits in line with one tube leg, so the branch leaves perpendicular to the supply run. On a PED run tee the thread sits opposite the branch, so the branch continues the run direction. Pick PEB when the branch must change plane, PED when the branch should carry straight on from the port.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEB T-Shaped Straight Thread Tee Connector PEB802
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.