Airtac PED T-Shaped Side Thread Tee Fitting PED601
The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED601 is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED601
The PED601 is an AirTAC PED male run tee in the resin one-touch family. It joins two legs of Dia 6 mm soft nylon or polyurethane tubing and carries a 1/8" PT male stud positioned in the run of the tee, so the stud sits in-line with one tube leg while the second tube leg leaves at 90 degrees. This run-through geometry is what separates PED from the PEB branch tee, where the male thread is on the perpendicular leg instead.
Connection is push-to-seal: push the tube firmly into the chuck until it bottoms, and the stainless spring gasket and POM chuck grip and seal it; press the release ring to free it. As a resin one-touch part it is rated 0-1.0 MPa (0-10 kgf/cm2) working, 1.5 MPa proof, -750 mmHg (10 Torr) vacuum and -20 to +70 C. The body is PBT with a brass stud, and the 1/8" thread arrives with sealant already applied - M5 sizes in this range use a sealing gasket instead, but this stud does not need tape.
Airtac PED T-Shaped Side Thread Tee Fitting PED601 Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED601 |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED601
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED601 Is Used
Solenoid valve manifold branching
Screw the 1/8" stud into a spare port on a pick-and-place gripper manifold and split the Dia 6 mm supply into two push-in legs feeding left-hand and right-hand suction cups from one tap.
Twin blow-off nozzles on a bottling line
Tee a Dia 6 mm line at the cooling station so one 1/8" run-tee stud takes plant supply while both tube legs continue to paired air-nozzle rinse jets over the bottle conveyor.
Pressure gauge tap on a test rig
Insert the run tee mid-line in a Dia 6 mm nylon circuit on a pneumatic leak-test bench so the in-line 1/8" stud carries a gauge or transducer without cutting and re-fitting the main run.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED601 the Right Part?
Both neighbours exist at this thread. Step down to PED401 (Dia 4 tube) when the line feeds a small gripper or pilot port where a 6 mm bore is more airflow than the actuator needs; step up to PED801 (Dia 8 tube) when the branch feeds a cylinder with higher consumption and you want less pressure drop over a longer run. On the thread side, PED602 (1/4") gives a stiffer stud for larger manifold ports, while a PED M5 version covers Dia 6 down to the smallest tapped ports - both are in the PED ladder.
Match the stud to a genuine 1/8" PT tapped port and remember tube OD must match exactly: a Dia 6 fitting will not seal or hold 1/4" (6.35 mm) tube, which is a different size. If your port is a wall you tap into sideways rather than a point along the main run, the PEB male branch tee puts the stud on the 90-degree leg instead and is the better shape.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED601 FAQ
This SKU is a Dia 6 mm tube male run tee with a 1/8" PT male stud. Resin one-touch ratings: working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, and a temperature range of -20 to +70 C. Use soft nylon or polyurethane tubing of exactly Dia 6 mm on both tube legs.
No. AirTAC ships this threaded one-touch fitting with sealant already applied to the 1/8" PT thread, so it can be screwed straight into a tapped port; sealing tape is only likely to shed debris into the circuit. Note that the smallest M5 versions in this series use a sealing gasket rather than sealant, and that the stud on a PED sits in the run of the tee - if you need the male thread on the 90-degree leg, order a PEB branch tee instead.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED601
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.