Airtac PED T-Shaped Side Thread Tee Fitting PED601D-S
SUS304 stainless variant (-S)The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED601D-S is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED601D-S
The PED601D-S is an AirTAC PED male run tee in the resin one-touch family, joining Dia 6 mm soft nylon or polyurethane tube on both run legs and offering a male 1/8" PT thread that sits in the straight-through run, not on the branch. The -S suffix means the threaded stud is SUS304 stainless steel while the body stays glass-reinforced PBT in black, the D colour code. Push the tube into the port and the stainless spring gasket chuck grips it; press the POM release ring to free it again.
Ratings are the standard resin profile: 0-1.0 MPa working pressure, -750 mmHg vacuum, 1.5 MPa proof, and -20 to +70 C. The 1/8" thread arrives with sealant already applied on the taper, so the stud can be screwed straight into a PT port, while the inline layout lets the main Dia 6 line continue past the connection without an extra coupling.
Airtac PED T-Shaped Side Thread Tee Fitting PED601D-S Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED601D-S |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED601D-S
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED601D-S Is Used
Branching off a manifold regulator
Thread the SUS304 stud directly into a filter-regulator outlet on a machine manifold and keep the Dia 6 main line running through the tee to the next drop, with the tube ports one-touch locked.
Coolant-mist machine tool panels
On surface-grinding and milling cells where mist attacks plated brass studs, the SUS304 stud resists the staining that eventually seizes ordinary fittings during panel servicing.
Packaging line vacuum generator feed
Feed a compact ejector on a carton-sealing conveyor from a Dia 6 branch while the run continues downstream, keeping the supply line intact without adding a separate union.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED601D-S the Right Part?
On the PED 1/8" row the ladder runs Dia 4, 6, 8 and 10. Step down to PED401-S when the branch feeds a small pilot circuit or a thin Dia 4 line; step up to PED801-S when the run carries the main feed to a larger cylinder or valve manifold, at the cost of a wider body across the run. Thread choice stays 1/8" here - if the port is 1/4" you need the PED602-S instead.
Tube OD must match exactly: this port is machined for Dia 6 mm only and will not seal on 1/4 inch (6.35 mm) imperial tube. If you need the male thread at a 90 degree end rather than in the run, that is a PL male elbow or a PEB branch tee, not a PED.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED601D-S FAQ
It is an AirTAC PED male run tee for Dia 6 mm soft nylon or polyurethane tube with a male 1/8" PT thread carrying SUS304 stud material on a black PBT body. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, and working temperature -20 to +70 C. Flow is published only as a characteristic curve, so size by tube bore, not by a Cv figure.
No. The -S suffix changes only the stud material to SUS304; every pressure, vacuum and temperature figure matches the standard PED601D, and the dimensions are identical, so it is a direct swap on existing Dia 6 / 1/8" pipework. Note the body itself remains PBT - only PC and POC straight connectors get a solid stainless body in this catalogue.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED601D-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.