Airtac PED T-Shaped Side Thread Tee Fitting PED602
The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED602 is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED602
The PED602 is an AirTAC PED male run tee, a three-port one-touch fitting where the 1/4in PT male thread sits in line with the run, so two Dia 6 mm tubes pass straight through the fitting and the third Dia 6 mm port branches at 90 degrees. Push each tube into its chuck until it bottoms; the stainless spring gasket and POM chuck grip it against the -750 mmHg vacuum to 1.0 MPa working range, and pressing the release ring frees it again.
This is the resin/brass spec profile, not the metal BP line: working pressure 0-1.0 MPa (0-10 kgf/cm2), proof pressure 1.5 MPa, temperature -20 to +70 C, for soft nylon or polyurethane tubing. The threaded body is PBT over a brass stud, and the thread arrives from AirTAC with sealant already applied, so no extra PTFE tape is needed on the PT port.
Airtac PED T-Shaped Side Thread Tee Fitting PED602 Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED602 |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED602
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED602 Is Used
Packaging machine trunk split
On a horizontal flow-wrapper frame, the PED602 lets a Dia 6 mm trunk from the FRL continue straight through while the in-line 1/4in port ties into the machine's valve manifold, and the perpendicular port drops a Dia 6 mm feed to the sealing-jaw cylinder.
Valve manifold tap-off
Screw the in-line 1/4in PT thread into a spare manifold station and use the two through ports to carry the Dia 6 mm main onward, turning one station into a three-way node without a separate junction block.
Vacuum pick-and-place feed
Rated down to -750 mmHg (10 Torr), the PED602 suits a carton-erector cell where the same Dia 6 mm line alternately supplies the vacuum ejector for suction cups and the blow-off pulse between cycles.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED602 the Right Part?
Size it against the ladder both ways. Down one tube step, the PED402 keeps the same 1/4in thread on a Dia 4 mm run - lighter, for signal-speed actuator feeds or thin cabinet wiring-adjacent routing. Up one step, the PED802 handles a Dia 8 mm trunk with more effective bore for longer runs to a cylinder cluster. On the thread side, PED601 drops to 1/8in for compact valve ports and PED603 steps to 3/8in where the port was drilled for a higher-capacity main. Dia 6 on 1/4in is a strong mid-ladder pair: enough bore to feed several Dia 4 mm take-offs downstream without starving them.
Choose a run tee (PED) rather than the PEB branch tee when the male thread must continue the straight-through run - PEB puts its thread on the perpendicular leg instead. And match the tube exactly: a Dia 6 mm chuck will not seal on 1/4in (6.35 mm) tube, so do not substitute.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED602 FAQ
It is a PED male run tee for Dia 6 mm soft nylon or polyurethane tube with a 1/4in PT male thread. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, and temperature range -20 to +70 C. This is the resin/brass profile; the metal BP-family parts have different figures. No flow coefficient is published - capacity follows the characteristic curve for the Dia 6 mm bore.
Both join three Dia 6 mm tubes to a male thread, but the thread position differs: on the PED the 1/4in male thread lies in line with the straight-through run, while on the PEB it sits on the perpendicular branch leg. Pick PED when the supply should keep flowing straight past the tap; pick PEB when the port feeds sideways off the run.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED602
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.