Airtac PED T-Shaped Side Thread Tee Fitting PED602-S
SUS304 stainless variant (-S)The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED602-S is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED602-S
The AirTAC PED602-S is a male run tee in the resin one-touch range, made for Dia 6 mm soft nylon or polyurethane tubing and a 1/4 inch PT male thread. On a run tee the thread sits on the run axis, so one tube leg lines up straight with the port while the second tube leg branches off at 90 degrees - unlike the PEB branch tee, where the thread is on the stem instead. To make a joint you simply push the tube home; the stainless spring gasket and internal chuck grip the OD, and pressing the POM release ring lets the tube back out again.
This is the resin/brass spec profile, not the metal BP line: working pressure 0-1.0 MPa, vacuum down to -750 mmHg, proof pressure 1.5 MPa, and a service range of -20 to +70 C. The thread is machined to PT as standard and arrives with sealant already applied, so the 1/4 in stud seals straight into the port without extra tape. The -S suffix fits a SUS304 stud while the tee body itself stays glass-reinforced PBT - the pressure, vacuum and temperature figures are identical to the grey standard version.
Airtac PED T-Shaped Side Thread Tee Fitting PED602-S Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED602-S |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED602-S
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED602-S Is Used
Wash-down branch on a meat-plant sorting conveyor
Tee the 1/4 in port on the gate cylinder's supply run and continue in Dia 6 mm PU tube, with the SUS304 stud standing up to daily caustic hose-down where a bare brass stud would pit.
Plating-line actuator feed in corrosive fume
Branch off an acid-mist-exposed air run on an electroplating hoist, taking Dia 6 mm nylon tube to the lift cylinder while the stainless stud resists the vapours attacking plain fittings.
Valve manifold tap on a textile winding machine
Screw the 1/4 in stud into the machine's air-preparation manifold and split the flow: one Dia 6 mm leg continues in line, the other feeds the yarn-tensioner clamp at 90 degrees.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED602-S the Right Part?
On the 1/4 inch rung of the PED ladder, PED402 steps down to Dia 4 mm for pilot and signal lines, and PED802 steps up to Dia 8 mm when you need a broader bore feeding a larger actuator - remember flow capacity follows the tube bore, not the thread. If the port is smaller, PED601 keeps the same Dia 6 tube on a 1/8 in thread; PED603 moves the same tube onto 3/8 in. Always match the fitting's tube size to the tubing OD exactly: a Dia 6 pocket will not seal on 1/4 inch (6.35 mm) tube, even though the numbers look close.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED602-S FAQ
It is a male run tee for Dia 6 mm tubing with a 1/4 inch PT male thread. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), negative pressure goes to -750 mmHg, proof pressure is 1.5 MPa, and the temperature range is -20 to +70 C. The male stud is SUS304 on this -S variant, the tee body is PBT with a POM release button, and it accepts soft nylon or polyurethane tube.
No. On the PED family the -S suffix converts the male stud to SUS304, while the tee body remains glass-reinforced PBT with the standard POM chuck and NBR seal. AirTAC publishes no rating change for the stainless version - pressure, vacuum, proof pressure and temperature are exactly the same as the grey PED602, and the dimensions match too.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED602-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.