Airtac PED T-Shaped Side Thread Tee Fitting PED603D-S
SUS304 stainless variant (-S)The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED603D-S is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED603D-S
The AirTAC PED603D-S is a male run tee from the resin one-touch family: Dia 6 mm soft nylon or polyurethane tube is pushed straight through the run of the tee and gripped by an internal chuck, while a 3/8in PT male thread branches off at 90 degrees to feed a port. Unlike a branch tee, the run stays in line with the tube path, so the main air flow sees a smooth straight-through passage and only the branch turns. This -S version carries a SUS304 stud on the threaded leg; the tee body itself remains PBT, finished in black because of the D suffix.
As a resin-line fitting it is rated 0-1.0 MPa working pressure, 1.5 MPa proof pressure, and -20 to +70 C, and it also holds -750 mmHg (10 Torr) on vacuum circuits. To make a joint, cut the tube square, push it into the collet until it seats, and the stainless spring gasket and NBR O-ring complete the seal; press the release ring to free it again. The 3/8in thread arrives with sealant applied, so no extra tape or compound is needed on the port.
Airtac PED T-Shaped Side Thread Tee Fitting PED603D-S Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED603D-S |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED603D-S
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED603D-S Is Used
Rotary indexing table supply
A 3/8in PT port on a rotary indexer's valve manifold tees off to two Dia 6 cylinder lines while the main run continues to the next station, all in one push-in part.
Plating line rinse station
The SUS304 stud on the threaded leg stands up to humid, chemically laden air around plating rinse tanks, where a plain brass stud would corrode at the port thread.
Black-painted packaging machine frame
Machine builders specify the black D-colour body so tube take-offs on a dark-painted packaging frame do not show stray grey fittings through the guards.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED603D-S the Right Part?
Within the PED row on a 3/8in thread, Dia 6 is the smallest tube offered - the next step up is Dia 8 on the PED803-S, which moves the branch into heavier cylinder and valve circuits at the cost of a larger pocket in the manifold face. If you step the thread down instead, PED602 gives the same Dia 6 tube on a 1/4in port; note that the 1/2in PED ladder starts at Dia 8, so Dia 6 on a 1/2in male run tee does not exist and should never be specified.
Choose the run-tee shape when a supply line has to continue past a take-off point: the through-run keeps the downstream line fed in a straight path. If the branch must pass through a panel wall, a PMF bulkhead connector is the right part; if the drop to the actuator needs to swivel, look at the PH universal male elbow instead. Whichever shape you pick, the tube OD must match exactly - a Dia 6 fitting will not grip 1/4in tube.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED603D-S FAQ
It is a male run tee joining Dia 6 mm soft nylon or polyurethane tube to a 3/8in PT male thread with a SUS304 stud on a PBT body. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), vacuum capability is -750 mmHg (10 Torr), proof pressure is 1.5 MPa, and the temperature range is -20 to +70 C. The -S suffix changes only the stud material; all ratings stay identical to the standard PED603D.
No. AirTAC publishes one rating for the PED family and the -S version carries exactly the same 0-1.0 MPa working pressure, 1.5 MPa proof pressure and -20 to +70 C range. The stud swaps to SUS304 for corrosion resistance at the port; the body stays PBT and the dimensions are unchanged, so it drops into the same footprint as the grey standard part.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED603D-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.