Airtac PED T-Shaped Side Thread Tee Fitting PED801D
The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED801D is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED801D
The PED801D is an AirTAC PED male run tee, the black D-suffix version in the resin one-touch range. It joins a Dia 8 mm tube to a 1/8in PT male thread while carrying the main line straight through the body and taking a 90-degree branch off the third port. Push the tube into the chuck until it bottoms, and the stainless spring gasket plus the gripping chuck lock it against pressure; press the POM release ring and the tube slides free. On this series the D suffix changes the body colour as well as the button, so the whole tee arrives black, which helps where fittings need to be visually matched to enclosures or kept distinct from grey utility lines.
This is the resin and brass profile, not the metal BP line: 0 to 1.0 MPa working pressure, -750 mmHg vacuum, 1.5 MPa proof pressure and -20 to +70 C. The 1/8in male thread is supplied with sealant already applied, so it seals straight into a PT-tapped port. Use soft nylon or polyurethane tube only, and match the 8 mm OD exactly - a 5/16in tube will not seat in the chuck.
Airtac PED T-Shaped Side Thread Tee Fitting PED801D Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED801D |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED801D
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED801D Is Used
Vacuum ejector take-off on a pick-and-place cell
A robotic palletiser runs an 8 mm nylon main along the gantry; the PED801D tees off mid-run to feed a compact ejector on the gripper, and the black body reads clearly against the stainless frame.
Pressure sensor tap on a compressor manifold
A 1/8in PT-tapped boss on an air receiver or manifold takes the male thread, while the Dia 8 line continues straight through to the point of use - the run-tee shape keeps the main flow path unbroken.
Ink distribution branch on a pad printer
Pad-printing heads need a clean air feed per colour station; the tee branches off the machine's main Dia 8 polyurethane line to each head's solenoid without adding extra couplings in the run.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED801D the Right Part?
On the PED 1/8in ladder the neighbours are PED601 (Dia 6 tube) below and PED1001 (Dia 10 tube) above. Stepping down to 6 mm gains compactness for light actuator feeds; stepping up to 10 mm raises the bore, so the through-flow and branch flow both rise where longer runs or hungrier cylinders are fed. If your port is 1/4in instead, the same Dia 8 tube is available as PED802.
Choose a run tee over a branch tee when the main line must continue unobstructed and the branch is the secondary take-off - for example, a gauge or sensor tap. If you need the branch to swivel into any angle rather than a fixed 90 degrees, the PH family is the better shape; if you want the tee to pass through a panel wall, look at the PMF bulkhead connector instead.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED801D FAQ
Working pressure 0 to 1.0 MPa (0 to 10 kgf/cm2), negative pressure down to -750 mmHg (10 Torr), proof pressure 1.5 MPa, and a temperature range of -20 to +70 C. The fitting joins Dia 8 mm soft nylon or polyurethane tube to a 1/8in PT male thread. It is the resin and brass one-touch profile with a POM release button and NBR O-ring; the D suffix gives it the black body and button.
No. AirTAC ships threaded one-touch fittings with sealant already applied to the thread, so the PED801D screws straight into a 1/8in PT-tapped port. Only the small M5 sizes in this catalogue use a sealing gasket instead. Keep in mind the thread standard here is PT - if your port is tapped NPT or BSPP/G, this part is not the match.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED801D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.