Airtac PED T-Shaped Side Thread Tee Fitting PED801D-S
SUS304 stainless variant (-S)The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED801D-S is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED801D-S
The PED801D-S is an AirTAC PED male run tee: an inline tee whose two tube ports sit on the same axis so the main line runs straight through, with a 1/8 inch PT male thread on that same run axis to screw the whole tee into a port or manifold. It accepts Dia 8 mm soft nylon or polyurethane tube on both tube ports. Connection is one-touch: push the tube firmly home and the internal chuck grips it against the spring gasket; press the release ring and the tube slides free for rework or rerouting.
This is the -S variant, so the male stud is SUS304 stainless steel; the tee body remains PBT, with a POM release button and chuck, aluminium-alloy guide, stainless spring gasket and NBR O-ring. It belongs to the resin one-touch line: working pressure 0-1.0 MPa (0-10 kgf/cm2), proof pressure 1.5 MPa, temperature -20 to +70 C, and a vacuum rating of -750 mmHg (10 Torr). The 1/8 inch thread arrives pre-coated with sealant, and the D in the code means the body itself is moulded in black rather than the standard grey.
Airtac PED T-Shaped Side Thread Tee Fitting PED801D-S Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED801D-S |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED801D-S
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED801D-S Is Used
Vacuum pick-and-place on carton packers
Run a single vacuum line straight through the tee and branch off to a second suction cup on the same end-of-arm tool. The -750 mmHg negative pressure rating covers light vacuum holding directly, with no separate vacuum fitting needed.
Fixed air drop to a gripper in a robotic cell
Screw the 1/8 inch PT stud into a port on the robot base or gripper manifold and let 8 mm polyurethane tube run on through the tee to the next axis, keeping the supply line continuous instead of dead-ended.
Rinse-adjacent air feeds on packaging machinery
Around filler and rinsing zones where splashed wash water attacks plated brass studs, the SUS304 male thread of the PED801D-S resists corrosion while the PBT body shrugs off routine washdown wetting.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED801D-S the Right Part?
On the 1/8 inch thread of a PED, Dia 8 sits between two real neighbours: PED601 (Dia 6) below and PED1001 (Dia 10) above. Stepping down to Dia 6 trims the bore feeding each leg of the run; stepping up to Dia 10 lowers resistance on longer runs or higher-draw branches. If your port is 1/4 inch PT instead, the Dia 8 equivalent is PED802. Match the thread to the port first, then the tube: a Dia 8 chuck will not seal on 1/4 inch (6.35 mm) tube, and tube OD must match the fitting exactly.
A run tee is the right shape when the branch must not disturb the main line's path - the through-line stays straight while the male thread feeds a fixed port. If you need the tee to pass through a panel wall instead, that is a bulkhead job (PMF family), not a PED.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED801D-S FAQ
It is an AirTAC PED male run tee for Dia 8 mm tube with a 1/8 inch PT male thread, black PBT body and SUS304 stud. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), proof pressure 1.5 MPa, temperature range -20 to +70 C, and it holds -750 mmHg (10 Torr) in vacuum. It accepts soft nylon or polyurethane tube, and flow is defined by the 8 mm bore rather than a published flow figure.
On the same 1/8 inch thread you can drop to PED601 for Dia 6 tube or step up to PED1001 for Dia 10 tube; both exist in the interface table. If the port you are threading into is 1/4 inch PT, order the Dia 8 equivalent PED802. Keep the tube OD identical to the fitting size in every case.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED801D-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.