Airtac PED T-Shaped Side Thread Tee Fitting PED803D
The AirTAC Airtac PED T-Shaped Side Thread Tee Fitting PED803D is a genuine male run tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale run tee
- SeriesPED
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PED T-Shaped Side Thread Tee Fitting PED803D
The PED803D is an AirTAC PED male run tee from the resin one-touch range, joining Dia 8 mm soft nylon or polyurethane tube to a 3/8 PT male thread. Unlike a branch tee, the threaded port on a run tee sits in line with the through-run, so the two tube legs form a straight passage and the thread taps into that run rather than off a perpendicular leg. Push the tube home and the internal chuck grips it under system pressure; press the release ring to free it again.
This is the resin and brass profile, not the metal BP line: working pressure 0-1.0 MPa, vacuum to -750 mmHg, proof pressure 1.5 MPa and a temperature span of -20 to +70 C. The 3/8 thread follows the PT standard and arrives with sealant already applied at the factory. The D suffix means the body itself is moulded in black, a practical choice on machines where grey fittings disappear against stainless framework.
Airtac PED T-Shaped Side Thread Tee Fitting PED803D Technical Specifications
| Model | Airtac PED T-Shaped Side Thread Tee Fitting PED803D |
|---|---|
| Type | Male run tee |
| Series | PED |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PED T-Shaped Side Thread Tee Fitting PED803D
| PED | Male run tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PED T-Shaped Side Thread Tee Fitting PED803D Is Used
In-line pressure gauge take-off on a pneumatic press
Tap the 3/8 PT port mid-run so a gauge or pressure switch reads circuit pressure where the flow actually passes, while the Dia 8 tube legs carry supply on to the press cylinder.
Blow-off feed along a bottling conveyor
Run Dia 8 tube the length of the conveyor frame and use the in-line thread to feed an air knife or nozzle manifold without breaking the straight path to downstream stations.
Mid-run valve tap on a packaging machine manifold
Insert the run tee between two Dia 8 tube spans and use the black 3/8 threaded body to mount a solenoid or shuttle valve directly in the supply line.
Is the Airtac PED T-Shaped Side Thread Tee Fitting PED803D the Right Part?
On the PED ladder this Dia 8 size sits between PED603 (Dia 6 tube, same 3/8 thread) and PED1003 (Dia 10 tube). Stepping down to 6 mm suits lighter-feeding legs and a slimmer envelope; stepping up to 10 mm pays off when the same run also supplies a larger actuator and you want the bore, not the fitting, to be the only restriction. Tube OD must match exactly - a Dia 8 chuck will not seal on 1/4 inch tube, which measures about 6.35 mm and looks deceptively close.
Match the 3/8 PT thread to the port it enters; stepping it down with a bushing on a 1/4 port is a common cause of over-torqued, leaking joints. If the gauge or valve port hangs off the end of the line instead of the middle, a PLL extended male elbow or a PL male elbow is the better shape. If the port genuinely branches at 90 degrees to the flow, the AirTAC PEB branch tee is the correct counterpart to this run tee.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PED T-Shaped Side Thread Tee Fitting PED803D FAQ
Working pressure is 0-1.0 MPa (0-10 kgf/cm2), with vacuum capability to -750 mmHg (10 Torr). Proof pressure is 1.5 MPa and the permitted temperature range is -20 to +70 C. The fitting joins Dia 8 mm soft nylon or polyurethane tube to a 3/8 PT male thread, in a black body. AirTAC publishes flow for the PED range as a characteristic curve only, so capacity should be judged by the 8 mm bore rather than a quoted flow number.
No extra sealing is normally needed: AirTAC ships this threaded one-touch part with sealant already applied to the PT thread. Sealing gaskets are only used on the M5 sizes in this catalogue, which this 3/8 version is not. Fit the tube fully home until it seats, and confirm the release ring still moves freely before pressurising.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PED T-Shaped Side Thread Tee Fitting PED803D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.