Airtac PEG T-Type Concentric Reducing Tee Fitting PEG6-4
The AirTAC Airtac PEG T-Type Concentric Reducing Tee Fitting PEG6-4 is a genuine different diameter tee for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeDifferent diameter tee
- SeriesPEG
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PEG T-Type Concentric Reducing Tee Fitting PEG6-4
The PEG6-4 is an AirTAC different diameter tee, a tube-to-tube reducing union that takes a Dia 6 mm main line and splits it into two legs, one of which accepts Dia 4 mm tubing. The reduction is moulded into one PBT body, so instead of buying a separate straight reducer plus an equal tee and stacking two joints, you make the whole branch take-off in a single fitting with one fewer leak path.
Connection is standard one-touch: push each tube firmly into its port until it bottoms out, and the internal chuck grips the OD to hold it under pressure; press the release ring to free it. This belongs to the resin/brass one-touch profile, which runs 0-1.0 MPa working pressure, -750 mmHg (10 Torr) vacuum, 1.5 MPa proof pressure and -20 to +70 C with soft nylon or polyurethane tubing. Grey body as standard; because this is a union with no threaded port, it arrives without thread sealant - that coating is reserved for the threaded series.
Airtac PEG T-Type Concentric Reducing Tee Fitting PEG6-4 Technical Specifications
| Model | Airtac PEG T-Type Concentric Reducing Tee Fitting PEG6-4 |
|---|---|
| Type | Different diameter tee |
| Series | PEG |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PEG T-Type Concentric Reducing Tee Fitting PEG6-4
| PEG | Different diameter tee. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PEG T-Type Concentric Reducing Tee Fitting PEG6-4 Is Used
Benchtop sample-handling rig
On a laboratory sample handler, a Dia 6 nylon trunk runs along the frame and the PEG6-4 drops a Dia 4 branch to a small ejector holding a vacuum cup - the -750 mmHg rating carries through the reduced leg.
Electronics pick-and-place gripper feed
A compact gripper on a PCB pick-and-place head only needs Dia 4 tubing; tapping the Dia 6 supply at the base of the arm with this tee keeps the run down the moving axis thin and light.
Packaging line labelling head blow-off
On a carton labeller, the Dia 6 main air line runs under the conveyor and this tee steps it down to a Dia 4 line feeding the small air jet that settles the label before the brush.
Is the Airtac PEG T-Type Concentric Reducing Tee Fitting PEG6-4 the Right Part?
PEG6-4 sits at the bottom of the reducing-tee ladder: there is no smaller different-diameter step in this range, so Dia 6 to Dia 4 is as low as it goes. Stepping up, the next real part is PEG8-6, which carries a Dia 8 main line down to a Dia 6 branch - useful when the branch itself still has to feed a second sub-branch. If all three legs must be the same diameter, choose a plain equal union tee instead of a reducer.
Match tube sizes exactly: the Dia 6 port will not seal on 1/4 in (6.35 mm) tube, and the Dia 4 port will not take 5/32 in. Where the branch has to reach a threaded port rather than continue in tube, a PED male run tee with its own thread is the better shape.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PEG T-Type Concentric Reducing Tee Fitting PEG6-4 FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), negative pressure down to -750 mmHg (10 Torr), proof pressure 1.5 MPa, and an operating temperature of -20 to +70 C with soft nylon or polyurethane tubing. This SKU joins Dia 6 mm tubing on the two through legs to Dia 4 mm tubing on the reduced branch, all in one push-fit body with no thread.
No. The PEG6-4 is a tube-to-tube union with no threaded port, so there is nothing to seal with tape or paste and nothing to torque - AirTAC publishes no tightening figure for it because none is needed. Push each tube in until it stops, confirm the chuck has gripped, and the joint is made. To remove a line, press the release ring on that port and pull the tube out.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PEG T-Type Concentric Reducing Tee Fitting PEG6-4
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.