Airtac PH-1 Hex Head Toggle Joint PH1002-S
SUS304 stainless variant (-S)The AirTAC Airtac PH-1 Hex Head Toggle Joint PH1002-S is a genuine universal male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeUniversal male elbow
- SeriesPH
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PH-1 Hex Head Toggle Joint PH1002-S
The AirTAC PH1002-S is a universal male elbow from the one-touch fitting range: a Dia 10 mm tube pushes straight into the chuck while the 1/4 in male thread below swivels, so the tube can leave at whatever angle the machine needs instead of the fixed 90 degrees of a PL elbow. That free orientation is the entire purpose of the PH prefix. AirTAC supplies the thread with sealant pre-applied, and the -S suffix puts a SUS304 stainless stud under the PBT elbow body.
This belongs to the resin and brass profile, not the metal BP line: working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum to -750 mmHg (10 Torr), proof pressure 1.5 MPa and a service temperature of -20 to +70 C. Inside, a POM release button and chuck grip the tube against a stainless spring gasket and NBR O-ring; press the collar and the tube frees again. The stainless stud changes no rating whatsoever - pressure, vacuum, proof pressure, temperature and every dimension match the standard grey PH1002.
Airtac PH-1 Hex Head Toggle Joint PH1002-S Technical Specifications
| Model | Airtac PH-1 Hex Head Toggle Joint PH1002-S |
|---|---|
| Type | Universal male elbow |
| Series | PH |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PH-1 Hex Head Toggle Joint PH1002-S
| PH | Universal male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PH-1 Hex Head Toggle Joint PH1002-S Is Used
Robotic palletizer wrist cylinder
A universal elbow lets the air line exit the gripper cylinder at whatever angle clears the wrist casting, with the 1/4 in thread still landing square in the port.
Electroplating transfer arm
The SUS304 stud stands up to periodic rinse and chemical splash around the threaded connection where a plain brass stud would dull and corrode first.
Vacuum sheet feeder on a carton erector
Rated to -750 mmHg (10 Torr), the Dia 10 bore feeds a venturi ejector while the swivel stud routes tubing cleanly away from the pick head.
Is the Airtac PH-1 Hex Head Toggle Joint PH1002-S the Right Part?
Down one step on the same 1/4 in thread is the PH0802 for Dia 8 tube; upward, there is no Dia 12 option on 1/4 in at all, because AirTAC caps the PH 1/4 in ladder at Dia 10 - to reach 12 mm you move to the 3/8 in thread and the PH1203. The same Dia 10 tube is also served by PH1003 (3/8 in) and PH1004 (1/2 in), so let the port on your valve or cylinder choose the thread and let the tube choose the first number. Whichever you pick, the chuck holds exactly one tube OD: this fitting will not seal 3/8 in hose or 12 mm tubing no matter how hard it is pushed home.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PH-1 Hex Head Toggle Joint PH1002-S FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum capability to -750 mmHg (10 Torr), proof pressure 1.5 MPa, temperature range -20 to +70 C. This SKU is the Dia 10 mm tube size with a 1/4 in PT male thread, supplied with sealant already on the thread. Soft nylon or polyurethane tubing only.
No. On the PH family the -S suffix makes the male stud SUS304; the elbow body stays PBT, with a POM release button, aluminium-alloy guide, stainless spring gasket and NBR O-ring. Pressure, vacuum, proof pressure, temperature and all dimensions are identical to the standard PH1002, so nothing needs re-rating.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PH-1 Hex Head Toggle Joint PH1002-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.