Airtac PHF Tandem Toggle Joint PHF1002D
The AirTAC Airtac PHF Tandem Toggle Joint PHF1002D is a genuine universal female elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeUniversal female elbow
- SeriesPHF
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PHF Tandem Toggle Joint PHF1002D
The PHF1002D is an AirTAC PHF universal female elbow: a swivelling one-touch fitting that lands Dia 10 mm soft nylon or polyurethane tube onto a 1/4 in female PT port. Because the whole elbow pivots on its thread, you can screw the fitting in square and then rotate the tube entry to face any direction the hose run needs - no re-tightening, no kinked tube. The female thread takes sealant at the factory, so the port sealing is handled before the part even reaches your bench.
This is a resin/brass part, not the metal BP line: working pressure 0-1.0 MPa (0-10 kgf/cm2), proof pressure 1.5 MPa, temperature -20 to +70 C, vacuum down to -750 mmHg (10 Torr). Internally it is the standard one-touch stack - POM release ring and chuck, aluminium-alloy guide, stainless spring gasket and an NBR O-ring. On the PHF series the D suffix changes the whole body to black, not just the button.
Airtac PHF Tandem Toggle Joint PHF1002D Technical Specifications
| Model | Airtac PHF Tandem Toggle Joint PHF1002D |
|---|---|
| Type | Universal female elbow |
| Series | PHF |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PHF Tandem Toggle Joint PHF1002D
| PHF | Universal female elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PHF Tandem Toggle Joint PHF1002D Is Used
Textile spinning frame air lines
Yarn-spinning frames carry compressed air to dozens of individual jet nozzles at odd angles along the machine length. The swivel body of the PHF1002D lets the 10 mm service line be aimed along the frame rail after the 1/4 in port is already torqued in, keeping runs straight and free of sharp bends.
Vacuum forming sheet clamps
Clamping beams on vacuum-forming and thermoforming machines use 10 mm tubing for hold-down cylinders mounted at angles that change with tooling. A universal female elbow on the beam's 1/4 in port lets each tooling change re-aim the hose entry without unscrewing the fitting, and the -750 mmHg vacuum rating covers the vacuum side too.
Pilot-plant reactor panel connections
Pilot-scale process rigs often terminate instrumentation air in female-threaded bulkheads and gauge stems. The 1/4 in female PT thread of this elbow lands directly on those pre-installed male studs, and the black PBT body keeps the fitting discreet on a stainless or dark-painted panel.
Is the Airtac PHF Tandem Toggle Joint PHF1002D the Right Part?
On the 1/4 in rung of the PHF ladder, Dia 10 is the top of the ladder: PHF accepts only Dia 6, 8 and 10 tube on a 1/4 in thread. Step down to PHF0802D (Dia 8) for lighter lines that feed small actuators or sensors; there is no Dia 12 at 1/4 in. If your line is Dia 12, move up to PHF1203D on a 3/8 in thread instead. Whatever you do, match the tube OD exactly - the chuck in a Dia 10 body will not seal on 12 mm tube or on 3/8 in imperial hose, and it will blow off under pressure.
Choose the universal female shape when the port itself is fixed but the hose direction is not: a manifold face, a valve subplate or a machine casting where a rigid PL male elbow would fight the routing. It is also the natural pick when the existing port already has a male stud or fitting installed and you need a female thread to land on.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PHF Tandem Toggle Joint PHF1002D FAQ
It is an AirTAC PHF universal female elbow with a Dia 10 mm one-touch tube entry and a 1/4 in female PT thread. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), proof pressure 1.5 MPa, negative pressure -750 mmHg (10 Torr) and temperature range -20 to +70 C. Suitable tubing is soft nylon or polyurethane in exactly Dia 10 mm OD, and the PT thread arrives with sealant applied.
Yes. The threaded body is screwed into the 1/4 in female port once, and the elbow section rotates around it, so the tube entry can be set to any angle after mounting. Note that the swivel aligns the fitting - it does not create a rotating air joint for spinning shafts, and it should never be used as a dynamic swivel on moving equipment.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PHF Tandem Toggle Joint PHF1002D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.