Airtac PHF Tandem Toggle Joint PHF1004D
The AirTAC Airtac PHF Tandem Toggle Joint PHF1004D is a genuine universal female elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeUniversal female elbow
- SeriesPHF
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PHF Tandem Toggle Joint PHF1004D
The PHF1004D is an AirTAC universal female elbow: a one-touch fitting whose 1/2in PT female thread seats onto a male port stud while the swivel body takes Dia 10mm tubing at whatever angle the run needs. Push the soft nylon or polyurethane tube home and the internal chuck grips the OD, backed by an NBR O-ring seal; press the POM release ring and the tube is free again without tools. The female thread is supplied pre-coated with sealant, so it beds straight onto the port.
This is the resin and brass one-touch profile, not the metal BP line: working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum to -750 mmHg, proof pressure 1.5 MPa and a temperature range of -20 to +70 C. On the D variant the body and release button are moulded black; the mechanics are identical. The threaded section is PBT over a brass stud, with an aluminium-alloy guide inside the collar.
Airtac PHF Tandem Toggle Joint PHF1004D Technical Specifications
| Model | Airtac PHF Tandem Toggle Joint PHF1004D |
|---|---|
| Type | Universal female elbow |
| Series | PHF |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PHF Tandem Toggle Joint PHF1004D
| PHF | Universal female elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PHF Tandem Toggle Joint PHF1004D Is Used
Robot gripper supply in a weld cell
A Dia 10 feed to a welding robot's parallel gripper has to clear the dress pack. The PHF1004D threads onto the wrist port and swivels so the tube exits away from the loom, even after the 1/2in thread has been fully tightened.
Carton erector venturi feed
Vacuum generators on case-erecting machines run under vacuum, and this fitting is rated to -750 mmHg. Use it to carry a Dia 10 supply line from the valve manifold to a venturi cartridge, with the elbow clocked to suit the mounting bracket.
Palletiser clamp cylinder drop
The 1/2in port on a palletiser's clamp cylinder often faces an awkward angle behind guarding. A universal female elbow at the port drops the Dia 10 run straight down to the manifold without adding a second fitting to the circuit.
Is the Airtac PHF Tandem Toggle Joint PHF1004D the Right Part?
Within the 1/2in thread row of the PHF ladder this Dia 10 sits between Dia 8 (PHF1002D) and Dia 12 (PHF1204D). Stepping down trims the bore for short, low-demand branches; stepping up adds capacity for longer drops feeding larger cylinders. On the thread side, 1/2in is the largest port PHF offers; the only step down is 3/8in (PHF1003D), which also accepts Dia 10 tube, so the tube run stays the same and only the port changes.
One caution before ordering: the chuck grips a true 10mm OD and nothing else, so 3/8in tube (about 9.5mm) or 12mm line will neither seal nor hold. And if the tube has to pass through a panel wall rather than turn at a port, that is a job for the PMF bulkhead connector instead of this elbow.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PHF Tandem Toggle Joint PHF1004D FAQ
It is a Dia 10 tube, 1/2in PT female universal elbow from AirTAC's resin one-touch range. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), proof pressure is 1.5 MPa, vacuum goes to -750 mmHg, and the temperature range is -20 to +70 C. Use soft nylon or polyurethane tube with a true 10mm OD.
Yes. Tighten the female thread first, then set the elbow body through a wide range of angles to point the tube where the run needs it - the main advantage over a fixed PL male elbow. To release the tube, press the POM release ring; the chuck grips a matching 10mm OD only.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PHF Tandem Toggle Joint PHF1004D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.