Airtac PL L Connector PL802D-S
SUS304 stainless variant (-S)The AirTAC Airtac PL L Connector PL802D-S is a genuine male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeMale elbow
- SeriesPL
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PL L Connector PL802D-S
The PL802D-S is AirTAC's PL male elbow in the one-touch range, joining Dia 8 mm soft nylon or polyurethane tube to a 1/4in PT male thread at a fixed 90 degrees. The body is moulded in black PBT (the D suffix sets the body colour on this series) and the threaded stud is SUS304 stainless steel. To connect, push the tube straight into the chuck until it bottoms out; the stainless spring gasket and collet grip the OD, and pressing the release ring lets the tube withdraw for re-routing.
This is the resin/brass pressure profile: 0 to 1.0 MPa working (0 to 10 kgf/cm2), -750 mmHg vacuum (10 Torr), 1.5 MPa proof pressure and -20 to +70 C. Note that the -S on a PL fitting upgrades the stud only - the body remains PBT, and the pressure and temperature ratings are identical to the grey standard version. The 1/4in thread arrives pre-coated with sealant, so no additional tape or paste is needed on assembly.
Airtac PL L Connector PL802D-S Technical Specifications
| Model | Airtac PL L Connector PL802D-S |
|---|---|
| Type | Male elbow |
| Series | PL |
| Connection | Push-in one-touch |
| Body material | Stainless steel 304 (-S variant) |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. Stainless (-S): SUS304 in place of brass - a solid SUS304 body on the PC and POC straight connectors, and a PBT body with a SUS304 stud on the elbow, tee and branch shapes. Working pressure, proof pressure and temperature are unchanged from the standard version. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PL L Connector PL802D-S
| PL | Male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
| -S | Stainless-steel body. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PL L Connector PL802D-S Is Used
Pick-and-place cylinder connection
On a pick-and-place module with a Dia 8 cylinder port, the PL elbow lets the 8 mm tube leave downward at 90 degrees inside a tight guard instead of sweeping across the stroke path.
Wet-zone machine manifold
On packaging or bottling machinery where condensate and wash-down spray sit on exposed threads, the SUS304 stud on the PL802D-S resists corrosion at the port while the PBT body stays light.
Conveyor stopper cylinder drop
A conveyor-mounted stopper or gate cylinder with a 1/4in PT port takes this elbow directly, dropping the tube neatly behind the side rail to the nearest valve station.
Is the Airtac PL L Connector PL802D-S the Right Part?
On the PL ladder with a 1/4in thread you can step down to Dia 6 or up to Dia 10. Going down to 6 mm suits lighter actuator circuits and narrower routing channels; stepping up to 10 mm lowers resistance through longer runs to larger-bore cylinders. Flow capacity tracks the 8 mm bore, so keep run length modest if your actuator speed budget is tight. Match the stud to the port - a 1/4in PT port on a valve or cylinder takes this directly, while M5 or 3/8in ports need a different SKU from the same PL family. The tube OD must match exactly: a Dia 8 chuck will not seal on 6 mm or 10 mm tube, and there is no clamp to rescue a mismatch. If you need to pass the thread through a panel wall instead, the PLM bulkhead male elbow is the shape to look at.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PL L Connector PL802D-S FAQ
This is a one-touch male elbow for Dia 8 mm tube with a 1/4in PT thread and a SUS304 stud. Working pressure 0 to 1.0 MPa (0 to 10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa, operating temperature -20 to +70 C. Tube options are soft nylon or polyurethane, and the stainless suffix does not alter any of these ratings.
On the PL family the -S makes the threaded stud SUS304 while the elbow body stays PBT - here in black because of the D suffix. It is a corrosion-resistance upgrade at the port interface, not a full stainless part and not a rating change. If your spec calls for a stainless body itself, that applies to the PC and POC straight connectors, not to this elbow.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PL L Connector PL802D-S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.