Airtac PLL L-Type Extended Thread Connector PLL1002D
The AirTAC Airtac PLL L-Type Extended Thread Connector PLL1002D is a genuine extended male elbow for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeExtended male elbow
- SeriesPLL
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PLL L-Type Extended Thread Connector PLL1002D
The PLL1002D is an AirTAC PLL male extended elbow, the resin one-touch fitting that joins Dia 10 mm soft nylon or polyurethane tubing to a 1/4 in PT male port at 90 degrees. The D suffix makes the PBT body black as well as the release button, so the fitting disappears against dark machine frames and anodised extrusion. Push the tube squarely into the chuck until it bottoms, and the stainless spring gasket and POM chuck grip it for a seal that holds straight through to -750 mmHg vacuum; press the release ring to free it again.
This belongs to the resin and brass one-touch profile, not the metal BP line: working pressure 0-1.0 MPa (0-10 kgf/cm2), proof pressure 1.5 MPa, temperature -20 to +70 C. The 1/4 in male thread arrives with sealant already applied, and because this is the extended PLL version the thread is longer than on a standard PL elbow, so it seats more deeply into thin-walled manifold ports and leaves room for a spanner behind close-fitting brackets.
Airtac PLL L-Type Extended Thread Connector PLL1002D Technical Specifications
| Model | Airtac PLL L-Type Extended Thread Connector PLL1002D |
|---|---|
| Type | Extended male elbow |
| Series | PLL |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PLL L-Type Extended Thread Connector PLL1002D
| PLL | Extended male elbow. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PLL L-Type Extended Thread Connector PLL1002D Is Used
Cylinder ports behind fixed guards
A 90 degree elbow on the rear port of a Dia 40-63 mm ISO cylinder keeps the drop out of the guard line, and the extended 1/4 in thread reaches through the boss so the sealant-coated thread is fully engaged rather than hanging at the surface.
Vacuum hold-down on cartoning lines
Rated to -750 mmHg, PLL1002D suits the suction side of small ejectors holding cartons or blister film on conveyor tooling, where the black body sits unobtrusively against dark vacuum plates and quick release speeds changeovers.
Pneumatic drops on robotics cells
Steering Dia 10 mm supply lines down from the dress-pack into a 90 degree turn at the wrist or base casting, the longer male thread of the PLL body seats solidly in tapped ports on the robot base without a extra spacer or bulkhead plate.
Is the Airtac PLL L-Type Extended Thread Connector PLL1002D the Right Part?
On the PLL 1/4 in ladder you can step down to the PLL0802 for Dia 8 mm runs - lighter tubing, lower force actuators, easier routing through tight bundles - or up to the PLL1202 for Dia 12 mm lines feeding larger bore cylinders and longer circuits where pressure drop in the tube matters more than the fitting. Dia 10 mm is the middle rung and the common choice for mid-size actuation. Whichever you pick, the tube OD must match exactly: this socket is machined for 10 mm tube and will not seal on 3/8 in hose, which is close but not the same.
Choose PLL over PL when the port wall is thin, when a locknut or gauge will share the connection, or when the fitting needs to stand proud of a recessed boss. If the geometry needs to swivel to align instead, look at the PH universal elbow family rather than forcing this fixed 90 degree body.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PLL L-Type Extended Thread Connector PLL1002D FAQ
It is a Dia 10 mm one-touch extended male elbow with a 1/4 in PT male thread and a black body. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), negative pressure goes to -750 mmHg (10 Torr), proof pressure is 1.5 MPa, and the operating temperature range is -20 to +70 C. It is designed for soft nylon or polyurethane tubing only.
No. The chuck and gasket are sized for a 10 mm outside diameter and a 3/8 in hose is roughly half a millimetre smaller, so the seal will not form and the tube can blow out under pressure. Measure the tube before ordering: if you are on true 3/8 in line, step to a different family, and if you are on 8 mm or 12 mm metric tube, order the PLL0802 or PLL1202 instead.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PLL L-Type Extended Thread Connector PLL1002D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.