Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF804
The AirTAC Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF804 is a genuine bulkhead connector for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeBulkhead connector
- SeriesPMF
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF804
The PMF804 is an AirTAC PMF bulkhead connector, the one-touch fitting made to carry an airline through a solid wall. It takes Dia 8 mm soft nylon or polyurethane tube on the push-in side and offers a 1/2in PT male thread on the other face. You drill a panel hole, pass the threaded stud through, and secure it with the dedicated bulkhead locknut - on Dia 8 fittings that locknut thread is M16x1, a detail worth knowing before you drill.
Connection is the standard one-touch action: push the tube home and the internal chuck grips it against the stainless spring gasket and NBR O-ring; press the POM release ring and the tube comes free. This is the resin and brass profile, not the metal BPC line - working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum to -750 mmHg, proof pressure 1.5 MPa, temperature -20 to +70 C. The 1/2in thread arrives with sealant already applied, and the standard body colour is grey.
Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF804 Technical Specifications
| Model | Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF804 |
|---|---|
| Type | Bulkhead connector |
| Series | PMF |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF804
| PMF | Bulkhead connector. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF804 Is Used
Control cabinet pass-through
Mount the PMF804 through the side wall of an electrical enclosure on a packaging line so the 1/2in PT manifold connection stays inside with the valves while the 8mm tube runs out to the grippers, keeping cable and airline routing separated.
Machine guard feed
Pass the fitting through the sheet-metal guard of a rotary indexing table so pneumatic lines to the clamp cylinders inside can be disconnected from outside without opening the guard, using the push-in release ring on the 8mm tube.
Laboratory bench panel
Fix the bulkhead stud into the back panel of a lab analysis bench and distribute clean dry air from the 1/2in PT supply to multiple 8mm drop lines feeding small pneumatic actuators and sample-handling devices.
Is the Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF804 the Right Part?
You have two ways to step from this SKU. On the tube side, PMF exists in Dia 6 and Dia 10 around this size: drop to 6 mm when the line on the far side of the panel feeds a small actuator or sensor port, go to 10 mm when the run is longer or the flow demand is higher - the bulkhead fitting itself is rarely the restriction, the bore is. On the thread side, the step down from 1/2in is PMF803 with a 3/8in PT stud, for manifolds and valve ports drilled at 3/8in. Remember PMF is never offered in M5, so a 1/2in stud like this one sits at the top of the thread ladder.
Match the 1/2in PT thread to a PT port or use a separate adapter; never force a BSPP or NPT nut onto it. And measure the tube before ordering: the chuck on this fitting holds exactly 8 mm OD tubing - a 5/16in or 1/4in tube will not seal in it, and tube OD must match the fitting size exactly.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF804 FAQ
Working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum down to -750 mmHg (10 Torr), proof pressure 1.5 MPa, operating temperature -20 to +70 C. The fitting joins Dia 8 mm soft nylon or polyurethane tube to a 1/2in PT male thread and mounts through a panel on an M16x1 bulkhead locknut. This is the resin and brass one-touch profile with a grey body.
Drill a hole sized for the M16x1 locknut shank, insert the threaded stud from the inside or outside depending on which face needs the 1/2in PT thread, then tighten the bulkhead locknut against the panel. The push-in side is then ready for 8 mm tube. Because the tube seals on the chuck at the fitting face, the panel wall itself carries no pressure, so a relatively thin enclosure or guard wall is sufficient.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PMF Female Thread Bulkhead Straight Through Fitting PMF804
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.