Airtac PZG Cross Reducing Fitting PZG12-10D
The AirTAC Airtac PZG Cross Reducing Fitting PZG12-10D is a genuine different diameter cross for push-in tube connection, rated 0 - 1.0 MPa (0 - 10 kgf/cm2) with a 1.5 MPa proof pressure.
- TypeDifferent diameter cross
- SeriesPZG
- Working pressure0 - 1.0 MPa (0 - 10 kgf/cm2)
- Proof pressure1.5 MPa
- Temperature-20 to +70 °C
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PZG Cross Reducing Fitting PZG12-10D
The PZG12-10D is an AirTAC different diameter cross - a four-way tube-to-tube union that joins Dia 12 and Dia 10 soft nylon or polyurethane tubing in a single push-in body. Four legs leave the junction at 90 degrees, so one feed line can be split and turned in two planes without a nest of separate tees and elbows. Push the tube home and the stainless spring gasket and chuck grip the OD; press the POM release ring toward the body and the tube frees again for rework.
This is the resin one-touch profile, not the metal line: working pressure 0-1.0 MPa (0-10 kgf/cm2), vacuum down to -750 mmHg (10 Torr), proof pressure 1.5 MPa and a service range of -20 to +70 C. The D suffix makes the PBT body black as well as the release button, which suits dark machine frames where a grey part would stand out. Sealing is by NBR O-ring at each chuck, and the 12 mm bore is the largest the one-touch tube ladder offers.
Airtac PZG Cross Reducing Fitting PZG12-10D Technical Specifications
| Model | Airtac PZG Cross Reducing Fitting PZG12-10D |
|---|---|
| Type | Different diameter cross |
| Series | PZG |
| Connection | Push-in one-touch |
| Working pressure | 0 - 1.0 MPa (0 - 10 kgf/cm2) |
|---|---|
| Negative pressure | -750 mmHg (10 Torr) |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Applicable tubing | Soft nylon or polyurethane tube |
| Thread standard | PT (Rc tapered) unless the code says otherwise |
POM release button and chuck, aluminium-alloy guide, stainless spring gasket, NBR O-ring; body brass or PBT depending on the part. AirTAC publishes flow as a characteristic curve rather than a single figure, so no L/min value is listed.
Model Code: Airtac PZG Cross Reducing Fitting PZG12-10D
| PZG | Different diameter cross. |
|---|---|
| 4 / 6 / 8 / 10 / 12 | Tube outside diameter in mm (3.2 mm exists on the mini series). |
| M5 / 01 / 02 / 03 / 04 | Thread: M5x0.8, 1/8", 1/4", 3/8", 1/2" (M3 on the mini series). |
| D | Black. Blank = grey. |
Fitting & Sealing Notes
- check Cut the tube square and clean before pushing it home, or the seal will leak.
- check Push until it stops, then pull back to check the chuck has gripped.
- check To release, press the collet ring fully in and pull the tube out.
- check Threaded parts arrive with sealant on the thread; M5 sizes use a sealing gasket.
- check Match the tube OD exactly - a 6 mm fitting will not hold 1/4" tube.
Where the Airtac PZG Cross Reducing Fitting PZG12-10D Is Used
Bottling line rail distribution
A Dia 12 trunk from the FRL arriving at a washer-filler conveyor splits here into Dia 10 drops feeding rail clamp and reject-blow cylinders in two directions.
Cartoniser vacuum pick and place
Cross junction on a suction-cup array where the -750 mmHg vacuum rating lets the same push-in body serve ejector feed legs at Dia 12 and cup legs at Dia 10.
Injection moulding cell services
Tucked behind the clamp unit of an all-electric press, the black PBT body disappears against dark machine frames while splitting ejector and core-pull air feeds.
Is the Airtac PZG Cross Reducing Fitting PZG12-10D the Right Part?
PZG12-10 is the top step of the different diameter cross ladder: 12 mm is the biggest tube the series takes, so there is no larger neighbour - the next combination down is PZG10-8, which gives up 2 mm of bore on both axes in exchange for a smaller body and lower-air-demand branches. If your split is all one size, the plain PZ same-diameter cross removes the step entirely; if you need a three-way rather than four-way split, look at PYW instead.
Tubing OD must match exactly on every leg. A Dia 12 port will not grip 1/2 in (12.7 mm) tube and the Dia 10 legs will not accept 3/8 in (9.5 mm), so convert the line before it reaches this fitting, not at it.
Quick checklist
- ✓ Tube outside diameter matches exactly
- ✓ Thread size and standard match the port
- ✓ Working pressure within 0 - 1.0 MPa (0 - 10 kgf/cm2)
- ✓ Temperature within -20 to +70 °C
Airtac PZG Cross Reducing Fitting PZG12-10D FAQ
It is a different diameter union cross joining Dia 12 and Dia 10 mm tube with no threaded port. Working pressure is 0-1.0 MPa (0-10 kgf/cm2), negative pressure -750 mmHg (10 Torr), proof pressure 1.5 MPa and temperature range -20 to +70 C. Tubing is soft nylon or polyurethane, and the D suffix denotes the black body.
No. One-touch chucks are cut for a single metric OD, so the Dia 12 legs grip only 12 mm tubing and the Dia 10 legs only 10 mm; 1/2 in (12.7 mm) and 3/8 in (9.5 mm) tube will neither seal nor release correctly. Use metric tube on both axes, or step to the PZG10-8 lower in the ladder if your branches are already 8 mm.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard parts are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC One-Touch Fittings
Request a Quote for Airtac PZG Cross Reducing Fitting PZG12-10D
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.