Airtac TACED Guided Compact Cylinder TACED63X15S
The AirTAC TACED Guided Compact Cylinder TACED63X15S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 15mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke15 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED63X15S
Double acting with a rod leaving both covers, the TACED63X15S pushes and pulls with identical force because each side works on the rod-side area: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa in either direction. Twin guide rods on the yoke stop the tooling from rotating and take side load, so a gripper or press plate stays square without an external guide. The 63 mm bore runs on 0.15-1.0 MPa (22-145 psi) of clean air and strokes at 30-500 mm/s.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why this size drops into tight fixtures, guarding and gantry frames. The hard-anodized aluminium body carries a roller-burnished bore, the S45C rod is hard-chrome plated, and fixed TPU bumpers absorb end-of-stroke energy at both ends. This -S model carries the optional magnet, so CMSE / DMSE switches can be fitted for end-position sensing.
Airtac TACED Guided Compact Cylinder TACED63X15S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED63X15S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 15 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED63X15S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED63X15S Is Used
Clamping fixture on a CNC machining centre
The 15 mm stroke is enough to swing a clamp arm in and out of the cut, and the 1458.1 N clamping force at 0.5 MPa holds a steel workpiece firmly against the fixture stop from either side of the cylinder.
Pick-and-place gripper for machined housings
The through-rod gives equal grip force opening and closing, and the twin guide yoke keeps the jaws aligned on an aluminium housing without twisting - roughly 74 kg of vertical lift margin covers a heavy casting.
Short-stake press in an electronics assembly cell
A compact benchtop stake or snap-fit press needs only 15 mm of travel; the short ISO 21287 body fits under a low gantry where a full-length profile cylinder would not, and 2041.3 N at 0.7 MPa seats the terminal.
Is the Airtac TACED Guided Compact Cylinder TACED63X15S the Right Cylinder?
At 63 mm bore this sits between the 50 mm size (881.2 N at 0.5 MPa) and the 80 mm size (2356.2 N at 0.5 MPa), so pick it when the 50 mm is under-rated for the job but 80 mm is oversized. The 15 mm stroke is well inside the standard range for this bore, so it ships as a catalogue item. If the load must stay put when air is lost, note that the piston will drift - add a rod lock or pilot check valve. FB flange mounting is available, and the -S magnet in this model lets you add CMSE / DMSE switches directly on the body slots.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED63X15S FAQ
Yes - because a rod exits both covers, both sides work on the rod-side area, so output is equal both ways: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa, with a maximum of 297.4 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, speed 30-500 mm/s, air filtered to 40 um.
The S in TACED63X15S means the optional -S magnet is fitted, so CMSE / DMSE reed or solid-state switches can be clipped into the slots around the hard-anodized aluminium body. Mounting is via the FB flange option, and the rod end carries a female M10x1.5 thread with a 1/8" air port. Fixed TPU bumpers at both ends absorb end-of-stroke impact; for outline details, confirm from datasheet.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED63X15S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.