Airtac BSE Clamp Standard Cylinder BSE80X1000
The AirTAC BSE Clamp Standard Cylinder BSE80X1000 is a genuine double-acting ISO 15552 cylinder with an integrated spring-applied, air-released ROD LOCK. If air is cut or an E-stop is hit, the collet clamps the Ø25mm rod and holds up to 3600 N in either direction — no drift. Ø80mm bore, 1000mm stroke, PT3/8 cylinder ports, G1/8 lock-release port.
- BoreØ80 mm
- Stroke1000 mm
- Static holding force3600 N
- Lock typeSpring-lock / air-release
- Cylinder portPT3/8
- Lock-release portG1/8
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac BSE Clamp Standard Cylinder BSE80X1000
The AirTAC BSE80X1000 is a double-acting ISO 15552 profile cylinder with an integrated spring-applied, air-released rod lock. It delivers a 3518 N push force at 0.7 MPa, while the collet lock provides a 3600 N bidirectional static holding force with zero live air. If air exhausts or an E-stop trips, the rod is held safely in place.
This unit runs at 0.15-0.7 MPa and unlocks via a separate G1/8 port. The lock is a holding device, not a dynamic brake: engage it only after the rod fully stops, balance pressures, and allow at least 0.5 s for release. This SKU lacks a magnet, so position sensing is not available.
Rod Lock — 3600 N Static Holding (Ø80mm)
A spring clamps the collet onto the rod, so the Airtac BSE Clamp Standard Cylinder BSE80X1000 holds its position in both directions when air is lost, exhausted or an E-stop trips. Apply 0.15–0.7 MPa to the G1/8 release port to unlock. Engage the lock only after the rod has stopped (it is not a dynamic brake), and release only when the pressures on both sides of the piston are balanced. Allow at least 0.5 s for full release before moving.
Airtac BSE Clamp Standard Cylinder BSE80X1000 Technical Specifications
| Model | Airtac BSE Clamp Standard Cylinder BSE80X1000 |
|---|---|
| Series | BSE ISO 15552 rod-lock cylinder |
| Bore size | Ø80 mm |
| Stroke | 1000 mm |
| Static holding force | 3600 N |
| Cylinder port | PT3/8 |
| Lock-release port | G1/8 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Unlocking pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC BSE datasheet. The lock uses the SE standard body; SE mounting accessories fit BSE except FTC. Port options: PT (standard) / G (BSPP); lock-release port is G1/8.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa (max) | 3519 N | — |
| Max drive (@0.7 MPa) | 359 kgf | |
Drive force is separate from the 3600 N static holding force of the lock. BSE operates up to 0.7 MPa. Size with a safety margin.
Model Code: Airtac BSE Clamp Standard Cylinder BSE80X1000
| B | Rod-lock cylinder prefix. |
|---|---|
| SE | ISO 15552 standard double-acting body. |
| 80 | Bore size in mm. |
| ×1000 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Thread: PT (blank) / G. Mounting (BSE): Basic, LB, FA, FB, CA, CB, CR, TC (FTC is not available on BSE). Related: SE (no lock), BSED (double-rod rod lock). Sensors CMSE/DMSE fit magnetic BSE.
Where the Airtac BSE Clamp Standard Cylinder BSE80X1000 Is Used
Palletizer Lift Carriage
Holds a 360 kg vertical lift carriage mid-travel during an E-stop, preventing uncontrolled drops when main air supply is lost.
Injection Mold Clamp
Locks the 3518 N extend stroke securely in place during mold changeovers, ensuring the platen cannot drift if air pressure bleeds out.
Heavy Divert Gate
Maintains a heavy routing gate fully extended across a conveyor lane, using the 3600 N hold to resist impact from passing packages.
Is the Airtac BSE Clamp Standard Cylinder BSE80X1000 the Right Cylinder?
Verify your load does not exceed the 3600 N static holding force. If you need less drive, the 63 mm bore offers 1559 N push at 0.5 MPa and 2200 N hold; if you need more, the 100 mm bore gives 3927 N push at 0.5 MPa and 5500 N hold. Always engage the lock only after the rod stops, and release it only when piston pressures are balanced.
At a 1000 mm stroke, side-loading is a major risk. Use a guide rail to prevent rod bending and premature seal wear. This cylinder uses a PT3/8 port, M20x1.5 rod thread, and standard SE mounting accessories fit perfectly except FTC.
Quick checklist
- ✓ Load to hold ≤ 3600 N?
- ✓ Fail-safe hold on air loss / E-stop needed
- ✓ Lock engaged only when stopped
- ✓ G1/8 release-air line available
- ✓ Magnet (-S) for CMSE/DMSE sensors?
Installation & Safety Notes
- check Engage the lock only after the rod has stopped — not as a dynamic brake.
- check Release only when both piston sides are pressure-balanced.
- check Allow ≥0.5 s for full release before commanding motion.
- check Feed the G1/8 release port with 0.15–0.7 MPa clean air.
- check Add safety-rated controls for man-rated / overhead loads.
- check Use SE mounting accessories (FTC excepted).
Airtac BSE Clamp Standard Cylinder BSE80X1000 FAQ
The lock is spring-applied and fail-safe. If air is lost, a collet clamps the rod instantly, providing a 3600 N bidirectional static hold. It is not a dynamic brake; the rod must be stopped before engagement.
Drive forces at 0.5 MPa are 2513 N push and 2268 N pull; at 0.7 MPa push is 3518 N (max 359 kgf). The separate static holding force of the lock is 3600 N.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC BSE Cylinders
Request a Quote for Airtac BSE Clamp Standard Cylinder BSE80X1000
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.