Airtac Adjustable Cylinder SAIJ32 SAIJ32AX200-75S
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32AX200-75S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 200mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ32 mm
- Stroke200 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac Adjustable Cylinder SAIJ32 SAIJ32AX200-75S
The AirTAC SAIJ32X200-75-S is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that creates a 125-200mm usable travel window.
Equipped with a magnet (-S), it supports CMSE reed and DMSE electronic sensors housed within the dual-side extruded aluminum barrel grooves. The rear stopper allows precise end-position tuning during commissioning without adding external stops, while the reduced SAIJ mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2) omits FB, CA, CB, and CR options.
Airtac Adjustable Cylinder SAIJ32 SAIJ32AX200-75S Technical Specifications
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32AX200-75S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 200 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac Adjustable Cylinder SAIJ32 SAIJ32AX200-75S
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac Adjustable Cylinder SAIJ32 SAIJ32AX200-75S Is Used
Product Changeovers
Dial in the exact end position for varying part sizes on a packaging line using the 75mm rear adjustment window, avoiding physical cylinder swaps.
Machine Commissioning
Fine-tune the retract stroke during initial setup to perfectly time machine sequences without fabricating external mechanical stops.
Is the Airtac Adjustable Cylinder SAIJ32 SAIJ32AX200-75S the Right Cylinder?
The generous 75mm adjustment window is ideal for product changeovers, allowing operators to dial in the exact stroke without swapping the cylinder.
For this 200mm stroke, the 12mm rod handles moderate side loads, but an external guide is recommended for heavy off-center loads. Because the rear adjuster acts only as a travel stop and the air cushion provides deceleration, neither will hold a load without live air; for true load-holding, consider an external rod lock or the SAIL lock variant. This dimensionally interchangeable ISO 15552 cylinder uses PT ports and a -S magnet.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac Adjustable Cylinder SAIJ32 SAIJ32AX200-75S FAQ
At 0.7 MPa, the push force increases to 563N.
The rear adjuster acts as a mechanical stop that allows you to shorten the effective travel from the nominal 200mm down to 125mm. It sets the end position but does not lock the load without live air pressure.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac Adjustable Cylinder SAIJ32 SAIJ32AX200-75S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.