Airtac Adjustable Cylinder SAIJ32 SAIJ32AX220-100
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32AX220-100 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 220mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ32 mm
- Stroke220 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac Adjustable Cylinder SAIJ32 SAIJ32AX220-100
The AirTAC SAIJ32X220-100 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that permits fine-tuning the retract end position. With a 220 mm nominal stroke and a 100 mm adjustment range, it provides a highly flexible 120-220 mm usable travel window for exact product changeovers.
It includes variable air cushions at both ends and omits the FB, CA, CB, and CR mounts, utilizing a reduced interface of Basic, FA, LB, TC, FTC, TCM1, and TCM2.
Airtac Adjustable Cylinder SAIJ32 SAIJ32AX220-100 Technical Specifications
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32AX220-100 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 220 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac Adjustable Cylinder SAIJ32 SAIJ32AX220-100
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×220 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac Adjustable Cylinder SAIJ32 SAIJ32AX220-100 Is Used
Product Changeovers
Dial the stroke back from 220 mm down to 120 mm to handle varying product lengths on the same line without adding external physical stops.
Commissioning Calibration
Fine-tune the retract end position during initial machine setup to perfectly dial in the 120-220 mm travel window.
End-Position Trimming
Use the 100 mm rear adjustment screw to precisely set the deceleration point without modifying the cylinder's ISO 15552 mounting footprint.
Is the Airtac Adjustable Cylinder SAIJ32 SAIJ32AX220-100 the Right Cylinder?
Choose this adjustable model over a fixed-stroke SAI when your machine setup requires variable end stops without physically swapping cylinders. If your application needs greater thrust, stepping up to the 40 mm bore yields 528 N of pull force at 0.5 MPa. The rear adjuster acts strictly as a travel stop for deceleration and does not hold the load without live air; for true drop protection, consider SAIL or BSAI. As a 220 mm stroke exceeds 300 mm, an external guide is not strictly mandated, but the 12 mm rod thread still requires attention to side-load limits. For a true ISO 15552 replacement, match the 32 mm bore, 220 mm stroke, 100 mm adjust, PT G1/8 port, and SUS420J2 rod material.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac Adjustable Cylinder SAIJ32 SAIJ32AX220-100 FAQ
It operates at speeds between 30 and 800 mm/s.
The rear adjuster allows you to shorten the effective travel by up to 100 mm, creating a usable stroke window of 120 to 220 mm. It functions as a mechanical stop and does not lock the load without air pressure.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac Adjustable Cylinder SAIJ32 SAIJ32AX220-100
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.