Airtac Adjustable Cylinder SAIJ32 SAIJ32AX95-10S
The AirTAC Airtac Adjustable Cylinder SAIJ32 SAIJ32AX95-10S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 95mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ32 mm
- Stroke95 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac Adjustable Cylinder SAIJ32 SAIJ32AX95-10S
The AirTAC SAIJ32X95-10-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. The integrated -S magnet enables position sensing with AirTAC CMSE reed or DMSE solid-state switches installed in the dual-side sensor grooves.
With a 10 mm adjustment range, this 95 mm stroke model yields a usable travel window of 85-95 mm, letting you dial in exact end positions at commissioning without adding external stops. The rod is constructed from SUS420J2 stainless steel for enhanced corrosion resistance, and the standard SAIJ mounting set omits FB, CA, CB, and CR brackets, offering Basic, FA, LB, TC, FTC, TCM1, and TCM2 options.
Airtac Adjustable Cylinder SAIJ32 SAIJ32AX95-10S Technical Specifications
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32AX95-10S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 95 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac Adjustable Cylinder SAIJ32 SAIJ32AX95-10S
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×95 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac Adjustable Cylinder SAIJ32 SAIJ32AX95-10S Is Used
Machine Commissioning
Fine-tune the 85-95 mm travel window during setup to hit exact end positions without swapping cylinders or adding external mechanical stops.
Product Changeover
Quickly adjust the retract end-stop by up to 10 mm when running a new product size on the line, minimizing downtime between production runs.
Position Verification
Leverage the -S magnet with DMSE solid-state sensors to confirm end-of-stroke positions while dialing in the 10 mm adjustment window.
Is the Airtac Adjustable Cylinder SAIJ32 SAIJ32AX95-10S the Right Cylinder?
Select this 32 mm bore when you need precise retract-end tuning that a fixed-stroke SAI cannot provide; if your application requires greater thrust, stepping up to the 40 mm bore yields 628 N at 0.5 MPa. Because the stroke is under 300 mm, side-load stress on the 12 mm rod is minimal, though long unsupported loads still require an external guide.
For ISO 15552 interchangeability, match the 32 mm bore, 95 mm stroke, 10 mm adjustment, PT G1/8 port, and -S magnet. Remember that the rear adjuster acts only as a travel stop and does not hold the load without live air; for true load-holding, consider the SAIL or BSAI series.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac Adjustable Cylinder SAIJ32 SAIJ32AX95-10S FAQ
If operated at 0.7 MPa, the push force increases to 563 N.
The rear adjuster screw allows you to shorten the 95 mm nominal stroke by up to 10 mm, creating an 85-95 mm usable travel window. It acts as a mechanical stop to fine-tune the retract position and is not a lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac Adjustable Cylinder SAIJ32 SAIJ32AX95-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.