Airtac Adjustable Cylinder SAIJ32 SAIJ32BX290-10
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32BX290-10 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 290mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ32 mm
- Stroke290 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac Adjustable Cylinder SAIJ32 SAIJ32BX290-10
The AirTAC SAIJ32X290-10 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that creates a 280-290 mm usable travel window from its 290 mm nominal stroke. This bore size uses a 12 mm rod and M10x1.25 threading, operating at speeds between 30-800 mm/s.
Because the stroke reaches 290 mm, the 12 mm rod requires external guide support to prevent excessive side-loading on the front cap. The extruded aluminum barrel includes sensor grooves on both sides, allowing you to add CMSE reed or DMSE electronic sensors later if position feedback becomes necessary. The rear adjuster acts purely as a travel stop for end-position tuning, not a load-holding lock.
Airtac Adjustable Cylinder SAIJ32 SAIJ32BX290-10 Technical Specifications
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32BX290-10 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 290 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac Adjustable Cylinder SAIJ32 SAIJ32BX290-10
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×290 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac Adjustable Cylinder SAIJ32 SAIJ32BX290-10 Is Used
Product Changeover
Dial in the 10 mm adjustment range to quickly accommodate slightly different product lengths on the line without changing the cylinder mounting.
Machine Setup
Fine-tune the retract end-position during initial commissioning, ensuring precise mechanical alignment without adding external stopper blocks.
Variable End Stops
Use the 280-290 mm travel window to set exact retraction depths for delicate positioning tasks in light assembly automation.
Is the Airtac Adjustable Cylinder SAIJ32 SAIJ32BX290-10 the Right Cylinder?
The SAIJ configuration omits the FB, CA, CB, and CR mounting options, supporting only Basic, FA, LB, TC, FTC, TCM1, and TCM2 interfaces. For any load-holding requirements without live air pressure, this cylinder will not suffice; you must integrate an external pilot-operated check valve or select the SAIL or BSAI series instead.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac Adjustable Cylinder SAIJ32 SAIJ32BX290-10 FAQ
The rear adjuster allows you to shorten the effective stroke by up to 10 mm, providing a usable travel window of 280-290 mm from the 290 mm nominal stroke. This stopper is designed for end-position tuning and does not lock or hold the load without live air pressure.
The maximum thrust is 82 kgf at 1.0 MPa.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac Adjustable Cylinder SAIJ32 SAIJ32BX290-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.