Airtac Adjustable Cylinder SAIJ32 SAIJ32BX450-10
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32BX450-10 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 450mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ32 mm
- Stroke450 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac Adjustable Cylinder SAIJ32 SAIJ32BX450-10
The AirTAC SAIJ32X450-10 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that creates a 440-450mm usable travel window. This configuration provides precise end-position tuning without swapping out the entire actuator.
Because the adjuster acts purely as a mechanical stop and does not lock the load, live air is required to maintain position. The extruded aluminum barrel includes sensor grooves on both sides, allowing for the easy addition of CMSE or DMSE switches if sensing is needed later.
Airtac Adjustable Cylinder SAIJ32 SAIJ32BX450-10 Technical Specifications
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32BX450-10 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 450 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac Adjustable Cylinder SAIJ32 SAIJ32BX450-10
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×450 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac Adjustable Cylinder SAIJ32 SAIJ32BX450-10 Is Used
Commissioning Calibration
Dial in the exact 440-450mm end-of-stroke position during initial machine setup to accommodate sensor targets or mechanical variances.
Product Changeover
Quickly trim the stroke up to 10mm on a packaging line when switching to a slightly different carton or product size.
Fixture Positioning
Fine-tune the retraction point of a clamping fixture without adding bulky external stopper blocks to the machine frame.
Is the Airtac Adjustable Cylinder SAIJ32 SAIJ32BX450-10 the Right Cylinder?
An adjustable stroke is preferred over a fixed SAI cylinder when you need to dial in a 440-450mm travel window during machine commissioning. For direct compatibility, match the 32mm bore, 450mm stroke, 10mm adjustment, PT ports, and standard mounting options.
With a 450mm stroke, the 12mm rod should be guided externally to prevent excessive side-loading and premature seal wear. If the machinery demands true load-holding without continuous air pressure, consider an AirTAC SAIL or BSAI cylinder instead of relying on this rear stopper.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac Adjustable Cylinder SAIJ32 SAIJ32BX450-10 FAQ
The maximum thrust is 82 kgf at 1.0 MPa.
The rear adjuster screw allows you to shorten the 450mm nominal stroke by up to 10mm, creating a 440-450mm travel window. It functions as a mechanical stop for end-position tuning and is not a locking device.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac Adjustable Cylinder SAIJ32 SAIJ32BX450-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.